1. Поставување
This section guides you through the initial preparation of your Brother LS-1217 sewing machine before its first use.
1.1 Отпакување и поставување
Carefully remove the sewing machine from its packaging. Retain all packing materials for future transport or storage. Place the machine on a stable, flat surface with adequate lighting. Ensure there is enough space around the machine for comfortable operation and fabric handling.
1.2 Поврзување за напојување
Connect the power cord to the machine's power input jack, then plug the other end into a standard electrical outlet. Ensure the power switch is in the "OFF" position before connecting. The foot controller also connects to a dedicated jack on the machine.
1.3 Инсталација на игла
- Turn the handwheel towards you to raise the needle to its highest position.
- Олабавете ја иглата клamp screw by turning it counter-clockwise.
- Вметнете нова игла со рамната страна свртена кон задниот дел од машината, туркајќи ја нагоре колку што може повеќе.
- Затегнете ја иглата clamp зашрафете безбедно.
1.4 Намотување на макарата
Proper bobbin winding is crucial for even stitching.
- Ставете калем од конец на иглата за калем.
- Водете го конецот низ горната водилка на конецот и околу дискот за затегнување на намотката на макарата.
- Insert the thread end into the small hole on the bobbin, from the inside out.
- Place the bobbin onto the bobbin winder spindle and push the spindle to the right.
- Press the foot controller gently to start winding. Stop when the bobbin is full and evenly wound.
- Cut the thread, push the spindle back to the left, and remove the bobbin.
1.5 Навојување на машината
Follow these steps for correct upper and lower threading.
Горен навој:
- Подигнете ја притисната нога и иглата на нивните највисоки позиции.
- Поставете го калемчето за конец на клинот на калемчето.
- Водете го конецот низ горната водилка за конец.
- Pass the thread down into the tension discs, then up and through the take-up lever from right to left.
- Guide the thread down through the remaining thread guides and finally through the eye of the needle from front to back.
- Pull about 6 inches of thread under the presser foot and towards the back.
Lower Threading (Bobbin Insertion):
- Отворете ја заштитната плоча на макарата.
- Вметнете ја намотаната калемка во кутијата на калемката, осигурувајќи се дека конецот се одмотува спротивно од стрелките на часовникот.
- Guide the thread into the tension spring of the bobbin case.
- Затворете ја заштитната плоча на макарата.
- Hold the upper thread lightly, turn the handwheel towards you to lower and raise the needle, catching the bobbin thread. Pull both threads under the presser foot and to the back.
2. Ракување со машината
This section details the basic operations for sewing with your Brother LS-1217.
2.1 Basic Stitch Selection
Your machine offers various stitch patterns. To select a stitch, turn the pattern selection dial until the desired stitch symbol aligns with the indicator mark. Refer to the stitch chart on your machine for available options.
2.2 Fabric Placement
Place the fabric under the presser foot, aligning the edge with the desired seam allowance guide on the needle plate. Lower the presser foot using the presser foot lever.
2.3 Starting to Sew
With the presser foot lowered, gently press the foot controller. The machine will begin to sew. Guide the fabric gently; do not pull or push it, as this can bend the needle or affect stitch quality.
2.4 Обратно шиење
To secure the beginning and end of a seam, use the reverse stitch lever. Press and hold the lever while sewing to stitch backward. Release the lever to resume forward stitching.
2.5 Finishing a Seam
When you reach the end of your seam, perform a reverse stitch for a few stitches, then release the foot controller. Raise the needle to its highest position and lift the presser foot. Pull the fabric towards the back, then cut the threads using the thread cutter on the machine or scissors, leaving about 4-6 inches of thread tails.
3. Одржување
Regular maintenance ensures the longevity and optimal performance of your Brother LS-1217.
3.1 Чистење на машината
Lint and dust can accumulate in the bobbin area and feed dogs, affecting stitch quality. Disconnect the machine from power before cleaning.
- Отстранете ја иглата, притисната ногарка и плочката на иглата.
- Use the small brush provided with your machine (or a soft brush) to remove lint from the bobbin case, feed dogs, and surrounding areas.
- Do not use compressed air, as it can push lint further into the machine.
- Избришете ја надворешноста на машината со мека, сува крпа.
3.2 Подмачкување
The Brother LS-1217 is designed to be largely maintenance-free regarding lubrication. Avoid applying oil unless specifically instructed by a qualified service technician, as improper lubrication can cause damage.
3.3 Замена на игла
Replace the needle regularly (approximately every 8-10 hours of sewing or after every major project) and immediately if it becomes bent, dull, or burred. A damaged needle can cause skipped stitches, thread breakage, and fabric damage. Refer to section 1.3 for installation instructions.
4 Смена на проблеми
Овој дел се однесува на вообичаени проблеми со кои може да се соочите и нуди решенија.
| Проблем | Можна причина | Решение |
|---|---|---|
| Прескокнати шевови | Incorrect needle installation, bent needle, wrong needle type for fabric, improper threading. | Reinstall needle correctly (flat side to back), replace bent needle, use appropriate needle for fabric, rethread machine completely. |
| Кршење на конец | Improper threading, incorrect tension, damaged needle, poor quality thread, bobbin wound unevenly. | Rethread machine, adjust tension, replace needle, use good quality thread, rewind bobbin evenly. |
| Fabric Jamming / Bunching | Improper threading, presser foot not lowered, excessive pulling/pushing of fabric, lint buildup. | Rethread machine, ensure presser foot is down, guide fabric gently, clean bobbin area and feed dogs. |
| Нерамни шевови | Incorrect tension settings, improper threading, dull needle, inconsistent fabric feeding. | Adjust upper and lower thread tension, rethread machine, replace needle, ensure consistent fabric guidance. |
| Машината не стартува | Power cord not connected, power switch off, foot controller not connected, bobbin winder spindle engaged. | Check power connections, turn power switch on, connect foot controller, disengage bobbin winder spindle. |
If these solutions do not resolve the issue, please contact customer support or a qualified service technician.
5. Спецификации
Key technical specifications for the Brother LS-1217 Sewing Machine.
- Модел: Brother LS-1217
- Видови бодови: Multiple utility and decorative stitches (e.g., Straight, Zigzag, Buttonhole)
- Систем на игли: HAx1 (130/705H)
- Напојување: AC 110-120V, 60Hz (North America) / AC 220-240V, 50Hz (Europe/Asia) - (Note: Actual voltage зависи од регионот)
- Димензии (приближно): 15.4" x 6.7" x 11.4" (39 см x 17 см x 29 см)
- Тежина (прибл.): 11 фунти (5 кг)
- Максимална брзина на шиење: До 750 бодови во минута
- Осветлување: Built-in sewing light
6. Гаранција и поддршка
For detailed warranty information, please refer to the warranty card included with your original purchase or visit the official Brother support webстраница. Зачувајте го доказот за купување за гаранциски побарувања.
Поддршка за корисници: For technical assistance, parts, or service, please contact Brother customer support. Contact details can typically be found on the Brother official webстраницата или во документацијата за вашиот производ.
Онлајн ресурси: Additional resources, FAQs, and video tutorials may be available on the official Brother support webсајт.