EVERYBOT Three-Spin Robot Mop TS300 Instruction Manual

1. Вовед

Thank you for choosing the EVERYBOT Three-Spin Robot Mop. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use and retain it for future reference.

Figure 1: EVERYBOT Three-Spin Robot Mop TS300

2. Што има во кутијата

По отпакувањето, проверете дали сите компоненти се присутни:

• EVERYBOT Three-Spin Robot Mop
• Лулка за полнење
• Далечински управувач
• Адаптер за напојување
• Mother-Yarn Mop Pads (for intensive mopping)
• Microfiber Mop Pads (for fine dust and polishing)
• Резервоар за вода
• Упатство за употреба

3. Поставување

3.1 Полнење на уредот

1. Place the charging cradle against a wall in an open area.
2. Поврзете го адаптерот за напојување со држачот за полнење и штекер.
3. Align the robot mop with the charging cradle. The device will automatically dock and begin charging. The battery indicator lights will illuminate.

3.2 Preparing Mop Pads

1. Select the appropriate mop pads (Mother-Yarn for intensive cleaning, Microfiber for polishing).
2. Moisten the mop pads with water and wring them thoroughly to remove excess water.
3. Attach the moistened pads to the rotating discs on the underside of the robot mop. They attach via Velcro.

3.3 Полнење на резервоарот за вода

1. Open the water tank cover located on the top of the robot mop.
2. Отстранете го резервоарот за вода.
3. Fill the tank with clean tap water. Do not add hot water or cleaning detergents to the tank, as this may damage the device or leave residue on your floors.
4. Securely close the water tank cap and reinsert the tank into the robot mop. Close the water tank cover.

Figure 2: Water Tank Filling Guidelines

4. Операција

4.1 Вклучување/исклучување

• To power on: Press and hold the power button on the device for approximately 3 seconds.
• To power off: Press and hold the power button for approximately 3 seconds.

4.2 Режими на чистење

The EVERYBOT Three-Spin offers 7 selectable cleaning modes via the remote control:

• Автоматско чистење: Basic mode for efficient room cleaning.
• Интензивно чистење: Repeats short forward movements and 360-degree rotations for meticulous cleaning.
• Focused Cleaning: Intensively cleans the nearby area based on the robot's current location.
• Чистење на рабовите: Directs the robot along walls and furniture edges.
• 50-minute Cleaning: Cleans for a set duration, suitable for separate rooms.
• Y-Mode Cleaning: Follows a Y-shaped pattern for thorough coverage.
• Рачно чистење: Allows direct control of the robot's movement using the remote.

Figure 3: Remote Control for Mode Selection

Figure 4: Visual Representation of Cleaning Modes

4.3 Паметни карактеристики

• Ултра тивка работа: Operates at an ultra-low 43 dB noise level.
• No-Wheel Structure: The 4.4 lb weight provides direct pressure for effective cleaning.
• Паметни сензори: Equipped with 11 anti-collision and fall prevention sensors to navigate safely and avoid obstacles or drops.
• Автоматско водоснабдување: The 300ml water tank automatically supplies water to the mops to maintain dampness.

Figure 5: Quiet Operation (43 dB)

Figure 6: Obstacle Avoidance with Smart Sensors

5. Одржување

5.1 Влошки за чистење на крпи

After each use, remove the mop pads. They can be hand-washed with water or machine-washed according to their care instructions. Ensure they are clean and dry before reattaching.

5.2 Сензори за чистење

Periodically wipe the 11 anti-collision and fall prevention sensors with a soft, dry cloth to ensure optimal performance.

5.3 Water Tank Care

Empty any remaining water from the tank after each use. Clean the tank regularly with water to prevent buildup. Do not use harsh chemicals.

6. Водич за решавање проблеми

If the red light flashes and error sounds persist, try the following steps:

1. Исклучено: Press the power switch for more than 3 seconds to turn off the device.
2. Управување со сензори: Remove any plastic film attached to the sensors. If there is dust or debris on the sensor, gently wipe it with a soft cloth.
3. Attach Mop Properly: Moisten the mop in water and wring it thoroughly. Attach the mop to the rotating disc slot. If the mop is too wet or not properly attached, the product may not operate correctly.

7. Спецификации

8. Видеа за производи

9. Гаранција и поддршка

For warranty information, technical support, or to purchase replacement parts, please refer to the official EVERYBOT webна локацијата или контактирајте ја службата за корисници. Зачувајте ја сметката за гаранциски барања.