FlyRobo BM730 3-in-1 Voltage Current Power Meter User Manual

Вовед

The FlyRobo BM730 is a compact 3-in-1 digital meter designed to measure DC voltage, current, and power simultaneously. It features a clear 4-digit LED display for easy reading and is suitable for monitoring battery levels, solar panels, and other DC systems. This manual provides essential information for safe and effective operation.

Информации за безбедност

• Always ensure proper wiring connections before applying power.
• Не надминувајте го наведениот волtage (0-100V DC) and current (10A) limits.
• Избегнувајте контакт со електрични кола под напон.
• This device is intended for DC circuits only.
• Да се ​​чува подалеку од дофат на деца.

Содржина на пакетот

Проверете дали сите предмети се присутни:

• 1x FlyRobo BM730 3-in-1 Voltage Мерач на струја
• 1x Wiring Harness for Power Supply (Thin Red/Black Wires)
• 1x Wiring Harness for Current Measurement (Thick Red/Black Wires)

Image: The BM730 meter shown with its two included wiring harnesses. One harness has thin red and black wires for power, and the other has thicker red and black wires for current measurement.

Производот завршиview

The BM730 meter features a multi-color LED display and control buttons for operation.

Слика: Горе view showing the digital display for voltage (V), current (A), and power (W), along with control buttons (Up, M, Down, R). Bottom view shows the circuit board with connection terminals.

Индикатори за прикажување:

• V (волти): Red display, indicates DC voltage.
• А (Ampерес): Green display, indicates DC current.
• W (Watts): Blue display, indicates DC power.

Контролни копчиња:

• Стрелка нагоре: Used for navigation or increasing values.
• М (режим): Used to switch display modes or confirm settings.
• Стрелка надолу: Used for navigation or decreasing values.
• R (Ресетирање): Used to reset readings or settings.

Спецификации

• Voltage опсег: 0V до 100V DC
• Тековен опсег: 0A to 10A DC
• Опсег на моќност: 0W to 1000W (calculated from V*A)
• Прикажи: 4-Digit LED (Red for V, Green for A, Blue for W)
• Димензии (Д x Ш x В): 80 mm x 41 mm x 26 mm
• Тип на мерење: Ammeter, Voltmeter, Wattmeter
• Извор на енергија: Battery Powered (self-powered from measured circuit or external supply)

Поставување и инсталација

Proper wiring is critical for the safe and accurate operation of the BM730 meter. Refer to the diagram below for connection details.

Приклучоци за жици:

1. Power Supply for Meter (Thin Red/Black Wires):

   Connect the thin red wire to the positive (+) terminal of your DC power source (0-100V).

   Connect the thin black wire to the negative (-) terminal of your DC power source.

   Note: The meter can be self-powered from the circuit it is measuring, or powered by a separate supply within its voltagд опсег.

2. Current Measurement (Thick Red/Black Wires):

   The thick red wire (IN+) and thick black wire (OUT-) are for current measurement. These wires must be connected in series with the load you wish to measure.

   Connect the thick red wire (IN+) to the positive side of the load.

   Connect the thick black wire (OUT-) to the negative side of the load, completing the circuit back to the power source.

   Важно: Do not connect the thick current wires directly across the power source; this will short the circuit and damage the meter or power source.

Осигурете се дека сите приклучоци се сигурни и изолирани за да спречите кратки споеви.

Упатства за работа

1. Вклучување: Once correctly wired, apply power to the circuit. The meter's display will illuminate, showing voltage, струја и отчитувања на моќност.
2. Приказ за читање:

   The top red display shows voltage во волти (V).

   The middle green display shows current in Ampерес (А).

   The bottom blue display shows power in Watts (W).

3. Функции на копчињата:

   The buttons (Up, M, Down, R) are typically used for fine adjustment, calibration, or alarm settings. Refer to specific advanced usage guides if available for detailed button functionalities. For basic operation, the meter displays readings automatically.
4. Overvoltage/Overcurrent Alarm: The meter supports an overvoltage and overcurrent sound alarm function. If the measured values exceed preset thresholds, an audible alarm may sound.

Одржување

• Keep the meter clean and dry. Use a soft, dry cloth to wipe the display and casing.
• Avoid exposing the meter to extreme temperatures, humidity, or corrosive environments.
• Не обидувајте се да го отворите casing or modify the internal circuitry, as this will void any warranty and may cause damage.
• Да се ​​чува на безбедно место кога не се користи.

Решавање проблеми

Мерачот не се вклучува:

Check the thin red and black power supply wires. Ensure they are correctly connected to a DC power source within the 0-100V range. Verify the power source is active.

Voltage displays, but current/power shows 0:

Ensure the thick red (IN+) and black (OUT-) current measurement wires are correctly connected in series with the load. The load must be drawing current for a reading to appear.

Неточни мерења:

Verify all connections are secure and free from corrosion. Ensure the meter is operating within its specified voltage и тековните опсези.

Audible alarm sounds:

This indicates an overvoltage or overcurrent condition. Check your circuit for excessive voltage or current draw and adjust as necessary.

Гаранција и поддршка

For warranty information or technical support, please contact FlyRobo directly. Refer to your purchase documentation for specific warranty terms.

Контакт информации за производителот: flyroboofficial@gmail.com