Opcom 1.99 OP COM OBD2 Car Diagnostic Tool User Manual

1. Вовед

The Opcom 1.99 OP COM diagnostic tool is a PC-based interface designed for diagnosing Opel (Vauxhall) vehicles. It features a PIC18F458 microcontroller and an FTDI chip for stable communication. This tool allows users to read and clear fault codes, view live data, and perform output tests on various control units within compatible Opel vehicles.

Клучни карактеристики:

• Верзија на фирмвер: V1.99
• Верзија на софтвер: V2014
• Equipped with PIC18F458 and FTDI chips for enhanced stability.
• Supports CAN-BUS based diagnostics.
• Compatible with most Opel cars up to the year 2014.

2. Информации за безбедност

Always exercise caution when working with vehicle electronics. Ensure the vehicle's ignition is off before connecting or disconnecting the diagnostic tool, unless instructed otherwise by specific diagnostic procedures. Refer to your vehicle's service manual for additional safety guidelines.

• Не обидувајте се да го отворите или модифицирате уредот.
• Keep the device away from water, extreme temperatures, and direct sunlight.
• Ensure proper ventilation when using the device with a laptop.

3. Содржина на пакетот

Проверете дали сите артикли се присутни во вашиот пакет:

• 1 x OPCOM Diagnostic Interface
• 1 x USB кабел
• 1 x Software and Drivers CD

An optional 10-pin to 16-pin adapter cable may be included or purchased separately for older Opel models.

4. Поставување

4.1 Системски барања

• Operating System: Windows XP or Windows 7 (32-bit recommended).
• USB порт: Достапен е USB 2.0 или 3.0 порт.
• Disk Space: Sufficient space for software installation.

Важно: Temporarily disable your anti-virus program during software installation to prevent interference.

4.2 Инсталација на софтвер

1. Insert the provided Software and Drivers CD into your computer's CD/DVD drive.
2. Follow the on-screen instructions to install the VAUX-COM software and necessary drivers.
3. If the CD is unreadable or damaged, please contact the seller for a download link to the software and drivers.

4.3 Хардверска врска

1. Connect one end of the USB cable to your computer and the other end to the OPCOM diagnostic interface.
2. Locate your vehicle's OBD2 diagnostic port, typically found under the dashboard on the driver's side.
3. Connect the 16-pin connector of the OPCOM diagnostic interface to the vehicle's OBD2 port.
4. For older Opel models that use a 10-pin connector, use the optional 10-pin to 16-pin adapter cable (if applicable) to connect the interface to the vehicle.

5. Операција

5.1 Starting the Software and Interface Test

1. Turn the vehicle's ignition to the 'ON' position (do not start the engine unless required by a specific test).
2. Launch the VAUX-COM software on your computer.
3. The software may automatically perform an interface test. Ensure you see a message indicating "Interface test ended successfully."

5.2 Идентификација на возилото

From the main menu, select 'Diagnostics'. You can choose to identify the vehicle automatically or manually by selecting the year and model from the provided lists.

5.3 Главни дијагностички функции

The VAUX-COM software supports various control units including Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, and Body Control Unit.

• Прочитајте и избришете ги кодовите за грешки: The program allows you to read out and clear diagnostic trouble codes (DTCs). Fault codes are displayed with full status information (Present, Not present, Intermittent). You can print, save, or copy these codes to other applications.

  

• Live Data (Measuring Blocks): View real-time data from various sensors and components. The program can display up to 8 measuring block parameters simultaneously. The sample rate varies depending on the communication protocol (e.g., older ISO-9141-2 systems are slower than newer KWP-2000 or CAN-BUS units).

  

• Output Tests: Perform specific output tests on many controllers to verify component functionality.

5.4 Протоколи за комуникација

The diagnostic interface acts as a multiplexer, selecting the appropriate pins for communication:

• PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000)
• HSCAN - Dual-wire, High Speed CAN-BUS, 500 kbps
• MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps
• SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps

6. Одржување

• Keep the diagnostic tool clean and dry. Use a soft, dry cloth for cleaning.
• Store the device in a safe place, away from dust and moisture, when not in use.
• Regularly check for software updates to ensure compatibility with the latest vehicle models and improved functionality.
• Inspect the USB cable and diagnostic connector for any signs of damage before each use.

7 Смена на проблеми

• Software CD Unreadable/Damaged: If you receive a damaged or unreadable software CD, please contact the seller directly to request a download link for the software and drivers.
• Software Not Launching/Working: Ensure your anti-virus program is temporarily disabled during installation and initial setup, especially on Windows XP and 7 (32-bit) systems, as it may interfere with the software or driver installation.
• Проблеми со поврзувањето:
  • Verify that the USB cable is securely connected to both the computer and the diagnostic interface.
  • Ensure the diagnostic interface is firmly plugged into the vehicle's OBD2 port.
  • Check if the correct drivers are installed for the device. You can usually verify this in your computer's Device Manager.
• Нема комуникација со возилото:
  • Confirm the vehicle's ignition is in the 'ON' position.
  • Ensure the vehicle model and year selected in the software match your vehicle.
  • For older vehicles, ensure the 10-pin to 16-pin adapter is correctly used if required.

8. Спецификации

9. Кориснички совети

• For optimal performance and to avoid software conflicts, it is highly recommended to temporarily disable your anti-virus software during the installation process and when running the VAUX-COM application, especially on older Windows XP/7 32-bit systems.
• The device is constructed from durable plastic, ensuring a robust build for regular use.
• The product has passed external testing certifications, indicating its safety for intended use.
• Always ensure your vehicle's battery is adequately charged before performing diagnostic procedures to prevent interruptions.

10. Најчесто поставувани прашања (ЧПП)

Q: What is the material quality of the device?

A: The device is made of plastic.

П: Дали уредот е безбеден за употреба?

A: Yes, it has passed external testing certification.

П: Кои оперативни системи се поддржани?

A: It can work on Windows XP and 7 (32-bit).

Q: What should I do if the software CD is unreadable or damaged?

A: Please contact the seller to obtain a download link for the software and drivers.

11. Гаранција и поддршка

For any technical assistance, troubleshooting, or inquiries regarding your Opcom 1.99 OP COM diagnostic tool, please contact the seller or the manufacturer's support channels. Keep your purchase records handy for faster service.