Вовед
The TP-LINK TX-6610 is a 1-Port Gigabit GPON Terminal designed to provide high-speed fiber optic network access. It complies with ITU G.984.x GPON standards, offering robust compatibility and performance for your internet connection. This manual provides detailed instructions for setting up, operating, and maintaining your TX-6610 device.
Врвот view of the TP-LINK TX-6610 GPON Terminal.
Содржина на пакетот
Пред да започнете, проверете дали вашиот пакет ги содржи следниве артикли:
- TP-LINK TX-6610 GPON Terminal
- Кабел за етернет RJ45
- Network Adapter (Power Supply)
- Водич за брза инсталација
Поставување
Follow these steps to set up your TX-6610 GPON Terminal:
- Позиционирање: Place the TX-6610 in a stable, well-ventilated location, away from direct sunlight and heat sources. Ensure it is within reach of your fiber optic connection and power outlet.
- Поврзете го оптичкиот кабел: Carefully connect the fiber optic cable from your service provider to the SC/APC Port on the TX-6610. Ensure the connector is clean and properly seated.
- Поврзете го етернет кабелот: Connect one end of the provided RJ45 Ethernet cable to the Gigabit RJ45 Port on the TX-6610 and the other end to your computer or router.
- Поврзете адаптер за напојување: Plug the network adapter into the power input port on the TX-6610, then plug the other end into a standard electrical outlet.
- Вклучување: Притиснете го копчето за вклучување/исклучување за да го вклучите уредот.
Аголна view of the TX-6610, highlighting the indicator lights and side port.
Оперативни
Once the TX-6610 is powered on, observe the indicator lights for its operational status:
- Моќност: Solid green indicates the device is powered on.
- GPON: Solid green indicates a successful connection to the GPON network. Blinking indicates data transmission.
- LOS (Губење на сигнал): If this light is red or off when it should be on, it indicates a problem with the fiber optic connection.
- LAN: Solid green indicates a successful Ethernet connection to a device. Blinking indicates data transmission.
The TX-6610 acts as a bridge between your local network and the GPON fiber network. Configuration is typically handled by your Internet Service Provider (ISP) via OMCI remote management. For advanced settings, you may access the device's web интерфејс за управување со користење на web browser, if enabled by your ISP.
Одржување
To ensure the longevity and optimal performance of your TX-6610:
- Чувајте го уредот чист и без прашина.
- Обезбедете соодветна вентилација за да спречите прегревање.
- Избегнувајте изложување на уредот на екстремни температури или влажност.
- Не обидувајте се да го отворите уредот casing, as this may void the warranty and expose you to electrical hazards.
- If the device is unresponsive, you can use the Копче RESET. Press and hold the RESET button for approximately 5-10 seconds to restore the device to its factory default settings. This will erase any custom configurations.
Решавање проблеми
If you encounter issues with your TX-6610, refer to the following common problems and solutions:
- Без светилка за напојување: Ensure the power adapter is securely connected to both the device and the electrical outlet. Try a different outlet.
- LOS Light is Red/Off: This indicates a loss of optical signal. Check the fiber optic cable connection to the SC/APC port. Ensure the cable is not damaged or bent sharply. Contact your ISP if the issue persists, as it may be a problem with their network or the fiber line.
- GPON Light Not Solid Green: The device is not successfully registered with the GPON network. Verify the fiber connection. Your ISP may need to provision the device.
- LAN Light Not On: Check the Ethernet cable connection between the TX-6610 and your connected device (computer/router). Try a different Ethernet cable or port on your connected device.
- Нема пристап до Интернет: Even if all lights appear normal, there might be an issue with your ISP's service or your router's configuration. Restart the TX-6610 and your router. If the problem continues, contact your ISP.
- Device Unresponsive/Frozen: Use the RESET button to restore factory defaults (see Maintenance section).
Спецификации
Хардверски карактеристики
| Карактеристика | Опис |
|---|---|
| Интерфејс | 1x 10/100/1000Mbps RJ45 Port, 1x SC/APC Port |
| Копчиња | 1x Power On/Off Button, 1x RESET Button |
| Надворешно напојување | 9VDC/0.6A |
| IEEE стандарди | IEEE 802.3, 802.3u, 802.1Q, 802.1p |
| Data Rate (Upstream) | 1.244 Gbps |
| Data Rate (Downstream) | 2.488 Gbps |
| Димензии (Ш x Д x В) | 4.0 x 1.5 x 4.2 инчи (102.7 x 37.9 x 106.9 mm) |
| Максимално растојание | 0 ~ 20 Km |
| GPON Standards | ITU-T G.984.1, G.984.2, G.984.3, G.984.4 |
| Оптички модул | Class C+, Receiver APD-TIA, DFB Laser Transmitter |
| Wavelength (Upstream) | 1310 nm |
| Wavelength (Downstream) | 1490 nm |
Софтверски карактеристики
| Карактеристика | Опис |
|---|---|
| QoS | VLAN-based Flow-Rating, Service Scheduling Rules (SP/WRR), Upstream Priority Label (802.1D), Rate Limit, Traffic Formation, Congestion Control (Tail-Drop) |
| VLAN | 802.1Q VLAN tag, Transparent/Translation/Trunk VLAN modes, Authentication by SN and Password, Auto Detection VLAN |
| Безбедност | AES Encryption, Packet Filter by VLAN |
| Управување | Web, OMCI, Telnet, Fixed-Management IP, Factory Default Reset (button/Web UI), Real-time Statistics, Optical Diagnostics |
| Напредни карактеристики | Upstream/Downstream FEC, Dynamic Bandwidth Allocation (DBA) compatible with NSR/SR (up to 16 T-CONTs and 256 GEM Ports), Optical power detection, Dying Gasp, Terminal Silent mechanism, Energy saving 802.3az EEE |
| IGMP | IGMP v2/IGMP v3 Snooping/Proxy |
| Сертификати | CE, FCC, RoHS |
| Системски барања | Microsoft Windows 98SE, NT, 2000, XP, Vista, 7, 8; MAC OS; NetWare; UNIX; Linux |
Услови на животната средина
| Состојба | Опсег |
|---|---|
| Работна температура | 0°C ~ 40°C (32°F ~ 104°F) |
| Температура на складирање | -40°C ~ 70°C (-40°F ~ 158°F) |
| Работна влажност | 10% ~ 90% некондензирачки |
| Влажност на складирање | 5% ~ 90% некондензирачки |
Совети за корисникот
Based on general user experiences with similar GPON terminals:
- Always ensure the fiber optic cable is not bent or kinked, as this can severely degrade signal quality.
- If you experience intermittent connectivity, try restarting both the GPON terminal and any connected router or computer.
- For optimal performance, connect your primary router directly to the Gigabit Ethernet port of the TX-6610.
Гаранција и поддршка
This TP-LINK product is covered by the manufacturer's warranty. Please refer to the warranty card included in your package or visit the official TP-LINK website for detailed warranty terms and conditions. For technical support, troubleshooting assistance, or service inquiries, please contact TP-LINK customer support or your Internet Service Provider (ISP).
