Ampролетна RS-1007 PRO аналоген Clamp Прирачник за корисник на метар

1. Вовед

На Amprobe RS-1007 PRO is an average-sensing, manual-ranging analog clamp meter designed for measuring alternating current (AC), AC voltage, and resistance. This instrument is suitable for electrical testing and heating, ventilation, and air-conditioning (HVAC) applications, particularly in environments where extreme temperatures might affect digital meters. Its analog display provides readings via a moving needle on a calibrated scale.

Главните карактеристики вклучуваат:

• Measures AC current up to 1,000 Ampерес.
• Мерки AC волtagд до 600 Волти.
• Measures resistance up to 1,000 Ohms.
• Трансформатор clamp with a 1.88-inch (47 mm) jaw opening for non-contact current measurement.
• Needle lock function to secure readings.
• Broader operating temperature range compared to digital multimeters.
• Meets IEC 61010 safety standard for CAT IV 600V installations.

2. Информации за безбедност

WARNING: To avoid electric shock or personal injury, read, understand, and follow all safety instructions and operating procedures before using this meter.

• Секогаш придржувајте се до локалните и националните безбедносни кодови.
• Не го користете мерачот ако изгледа оштетен или ако мерните сонди се оштетени.
• Пред да правите мерења, проверете дали мерачот е поставен на точната функција и опсег.
• Не ги надминувајте максималните ограничувања за внесување за која било функција.
• Бидете внимателни кога работите со волtagнад 30V AC RMS, 42V врв или 60V DC. Овие волумениtagтие претставуваат опасност од шок.
• Секогаш прво поврзувајте го заедничкиот (COM) мерен кабел, а потоа исклучете го последен.
• The meter is rated for CAT IV 600V installations, which covers measurements at the source of the low-voltagд снабдување.
• A finger guard on the body of the meter helps protect fingers from shock.

3. Производот завршиview

Familiarize yourself with the components of your Ampролетна RS-1007 PRO аналоген Clamp Метар.

Слика 1: Ampролетна RS-1007 PRO аналоген Clamp Мерач
This image displays the Ampролетна RS-1007 PRO аналоген Clamp Meter. Key features visible include the yellow clamp jaws at the top, the red main body, and the gray control panel. The control panel features an analog scale for readings, a 'LOCK' button, 'VA ZERO' and 'Ω ZERO' adjustment knobs, and input terminals for test leads labeled 'COM', 'A', and 'VΩ'. The meter also shows 'CAT IV 600V' and '1000A' markings on the jaws.

Компоненти на мерачот:

• Clamp Вилици: Се користи за бесконтактно мерење на наизменична струја.
• Jaw Opening Lever: Го отвора и затвора clamp вилиците.
• Analog Display Scale: Shows measurement readings via a moving needle.
• Needle Lock Button: Secures the needle position for reading retention.
• VA ZERO Knob: Adjusts the needle to zero for voltagе/струјни мерења.
• Ω ZERO Knob: Adjusts the needle to zero for resistance measurements.
• Прекинувач за избор на функција/опсег: Selects the measurement type (AC A, AC V, Ω) and range.
• Влезни терминали:
• COM: Common input terminal for all measurements.
• VΩ: Влезен терминал за voltage и мерења на отпор.
• A: Input terminal for current measurements (when using test leads, though primary current is via clamp).
• Заштитник на прстите: Provides protection against accidental contact with live circuits.

4. Поставување

4.1 Battery Installation (for Resistance Measurement)

The meter requires one 1.5V AAA battery (ANSI/NEDA-24A or IEC LR03) for resistance measurements. Current and voltage measurements do not require a battery.

1. Пронајдете го капакот на преградата за батерии на задната страна од мерачот.
2. Користете шрафцигер за да ја отворите преградата.
3. Insert one 1.5V AAA battery, observing correct polarity.
4. Вратете го капакот на преградата за батерии и прицврстете го.

4.2 Fuse Installation (for Resistance Measurement)

А 0.5 amp/1,000V fast-blow fuse is installed for resistance measurement protection.

1. The fuse is typically pre-installed. If replacement is necessary, refer to the battery compartment access.
2. Ensure the replacement fuse matches the specified rating (0.5A/1000V).

4.3 Тест поврзување на кабелот

За волtage and resistance measurements, connect the provided test leads:

• Вметнете го црниот тест одвод во COM влезен терминал.
• Вметнете го црвениот тест одвод во VΩ влезен терминал.

5. Упатства за работа

На Amprobe RS-1007 PRO is a manual-ranging meter, requiring the user to select the appropriate range for accurate measurements.

5.1 Measuring AC Current (Clamp Функција)

This method measures current without breaking the circuit.

1. Set the meter's function/range selector to the desired AC current range (e.g., 1000A).
2. Press the jaw opening lever to open the clamp вилиците.
3. Enclose a single conductor (not a bundle of wires) within the clamp вилици. Осигурајте се дека вилиците се целосно затворени.
4. Read the AC current value on the analog display scale.
5. If the needle goes off scale, select a higher range. If the reading is too low for accuracy, select a lower range if available.
6. За да го задржите отчитувањето, притиснете го копчето Заклучување со игла button. Release to allow the needle to move freely again.

5.2 Мерење AC Voltage

Use the test leads for voltagмерења.

1. Connect the test leads as described in Section 4.3 (black to COM, red to VΩ).
2. Set the meter's function/range selector to the desired AC voltage range (e.g., 600V AC).
3. Before connecting to the circuit, use the VA ZERO knob to ensure the needle is at zero.
4. Carefully connect the test probes in parallel across the circuit or component to be measured.
5. Прочитајте го AC voltage value on the analog display scale.
6. If the needle goes off scale, select a higher range. If the reading is too low for accuracy, select a lower range if available.

5.3 Measuring Resistance and Continuity

Resistance measurements require the installed 1.5V AAA battery.

1. Connect the test leads as described in Section 4.3 (black to COM, red to VΩ).
2. Set the meter's function/range selector to the desired resistance range (e.g., Ω).
3. Short the test leads together (touch the red and black probes).
4. Користете го Ω ZERO knob to adjust the needle to zero on the resistance scale.
5. Disconnect power from the circuit or component to be measured.
6. Поврзете ги тест сондите преку компонентата.
7. Read the resistance value on the analog display scale. A reading of zero or near zero indicates continuity.
8. If the needle does not move, the resistance may be too high for the selected range, or the circuit is open.

6. Одржување

6.1 Чистење

Избришете го мерачот со рекламаamp крпа и благ детергент. Не користете абразивни средства или растворувачи. Чувајте ги влезните терминали без нечистотија и влага.

6.2 Замена на батеријата

If the meter fails to zero for resistance measurements, or if the resistance readings become inaccurate, replace the 1.5V AAA battery as described in Section 4.1.

6.3 Замена на осигурувачите

If the resistance function ceases to operate, the 0.5 amp/1,000V fast-blow fuse may need replacement. Ensure the meter is disconnected from all power sources before opening the case to replace the fuse. Use only a fuse of the specified type and rating.

6.4 Складирање

When not in use, store the meter in its soft vinyl carrying case in a dry, dust-free environment. If storing for extended periods, remove the battery to prevent leakage.

7 Смена на проблеми

• Нема отчитување или отчитувањето е неточно:
  • Check if the meter is set to the correct function and range.
  • Осигурајте се дека тест каблите се правилно поврзани и не се оштетени.
  • For current measurements, ensure only a single conductor is within the clamp jaws and they are fully closed.
  • For resistance measurements, check the 1.5V AAA battery and fuse.
  • Ensure the circuit under test is de-energized for resistance measurements.
• Needle does not zero:
  • Користете го VA ZERO or Ω ZERO knob to adjust the needle.
  • If unable to zero for resistance, replace the 1.5V AAA battery.

8. Спецификации

Note: Some dimension and weight specifications provided in the source data appear to conflict. Please refer to the product packaging for the most accurate physical specifications.

9. Гаранција и поддршка

Amprobe manufactures electrical testing equipment. For product support, service, or warranty information, please contact Amprobe directly or visit their official website. The meter comes with a soft vinyl carrying case and instructions.

Посетете го официјалното лице Amprobe Store for more information: Amprobe Store on Amazon