Вовед
This manual provides essential information for the safe and effective use of the Hakko CHP TR-20-TM Micro Soft Wire Cutter. This precision tool is designed for cutting integrated circuit (IC) pins and soft wires up to 22 AWG (0.6mm).
Figure 1: Hakko CHP TR-20-TM Micro Soft Wire Cutter. This image displays the tool's overall design, highlighting its red and black ergonomic handles and the precise, angled cutting jaws.
Карактеристики на производот
- Reverse-Cut Micro Soft-Wire Cutter: Features an 8mm long jaw with a reverse angle head, specifically designed for flush-cutting IC pins up to 22 gauge (0.6mm).
- Angled Cutting Surface: The 48-degree reverse angled cutting surface facilitates precise cutting of closely-spaced IC pins.
- Издржлива конструкција: Constructed from 2.0mm heat-treated carbon steel for enhanced durability and extended tool life.
- Непречено работење: Precision-ground holes and surfaces ensure smooth movement of the cutting jaws.
- Reduced Operator Fatigue: An internal spring mechanism automatically returns the tool to the open position after each cut, minimizing hand strain.
- Ергономски дизајн: Dolphin-style nonslip hand grips provide comfort and control during prolonged use.
- Заштита за раце: A curved fore-edge on the handles protects hands from cutting surfaces.
- Отпорност на корозија: Parkerized surfaces prevent glare and increase the tool's resistance to corrosion.
Поставување
The Hakko CHP TR-20-TM Micro Soft Wire Cutter is ready for use out of the packaging. No assembly is required.
- Првична проверка: Before first use, inspect the tool for any signs of damage or manufacturing defects. Ensure the jaws align properly and the spring mechanism operates smoothly.
- Чистота: Ensure the cutting jaws are clean and free of debris before use to maintain optimal cutting performance.
Упатства за работа
Follow these instructions for safe and effective operation of the wire cutter.
- Безбедноста на прво место: Always wear appropriate eye protection when using cutting tools to prevent injury from flying debris.
- Зафат: Hold the cutter firmly with the ergonomic handles. The nonslip grips are designed for comfort and control.
- Позиционирање: Position the wire or IC pin to be cut between the jaws. For flush cuts on IC pins, align the reverse-angled jaw as close as possible to the circuit board or component body.
- Капацитет за сечење: Do not attempt to cut wires or materials exceeding the maximum capacity of 22 AWG (0.6mm) for soft wire. Cutting harder or thicker materials can damage the tool's jaws.
- Дејство на сечење: Apply steady, firm pressure to the handles to close the jaws and make the cut. The internal spring will reopen the jaws automatically upon release.
- Отстранување: Dispose of cut wire pieces responsibly.
Одржување
Proper maintenance ensures the longevity and performance of your Hakko wire cutter.
- Чистење: After each use, wipe the jaws and handles with a clean, dry cloth to remove any debris or residue. For stubborn grime, a slightly damp може да се користи крпа, по што темелно се суши.
- Подмачкување: Periodically apply a small drop of light machine oil to the pivot point to ensure smooth operation and prevent rust. Wipe off any excess oil.
- Складирање: Store the tool in a dry environment to prevent corrosion. Keep the jaws closed when not in use to protect the cutting edges.
- Избегнувајте паѓање: Dropping the tool, especially on hard surfaces, can misalign or damage the precision jaws.
Решавање проблеми
This section addresses common issues you might encounter with your wire cutter.
| Проблем | Можна причина | Решение |
|---|---|---|
| Jaws do not close completely or align properly. | Debris caught between jaws or pivot point; tool has been dropped or damaged. | Clean jaws thoroughly. If damage is suspected, discontinue use and consider replacement. |
| Cutting performance is poor or requires excessive force. | Dull or damaged cutting edges; attempting to cut material beyond capacity. | Inspect cutting edges for nicks or wear. Ensure material is within 22 AWG (0.6mm) soft wire limit. Replace if edges are significantly damaged. |
| Handles feel stiff or sticky. | Lack of lubrication at the pivot point; accumulation of dirt. | Clean the pivot area and apply a small amount of light machine oil. |
Спецификации
| Атрибут | Детал |
|---|---|
| Број на модел | TR-20-TM |
| Тип на вилица | Reverse-cut, Micro Flush-cut |
| Jaw Length | 8 мм |
| Агол на вилицата | 48-degree reverse angle |
| Максимален капацитет за сечење | 22 AWG (0.6mm) soft wire / IC pins |
| Градежен материјал | 2.0mm Heat-treated Carbon Steel |
| Материјал за рачка | Alloy Steel with Nonslip Grips |
| Боја | Црвено |
| Тежина на ставката | 0.1 фунти (приближно 45 грама) |
| Производител | Quality Hand Tools |
Гаранција и поддршка
For warranty information or technical support regarding your Hakko CHP TR-20-TM Micro Soft Wire Cutter, please contact American Hakko Products directly. American Hakko Products manufactures soldering and desoldering tools and is headquartered in Valencia, CA.
Please refer to the official Hakko website or your purchase documentation for the most current warranty terms and contact details.
Производител: Quality Hand Tools (as listed on product specifications, associated with Hakko brand)
Бренд: Хако
Webсајт: www.hakko.com
