HP ProLiant DL360 G9 1U Rack Server User Manual

Вовед

This manual provides essential information for the safe and efficient use of your HP ProLiant DL360 G9 1U Rack Server. It covers installation, operation, maintenance, and troubleshooting procedures. Please read this manual thoroughly before operating the server and retain it for future reference.

Информации за безбедност

Внимавајте на следниве безбедносни мерки за да спречите повреди и оштетување на опремата:

• Обезбедете правилно заземјување за сите електрични приклучоци.
• Do not operate the server with covers removed unless specifically instructed for maintenance.
• Disconnect all power cords before performing any service or upgrade procedures.
• Use only approved power supplies and cables.
• Install the server in a well-ventilated area to prevent overheating.
• Avoid spilling liquids on the server.

Содржина на пакетот

Проверете дали сите артикли се присутни во пакувањето:

• HP ProLiant DL360 G9 1U Rack Server
• Rack mounting hardware kit
• Кабли за напојување
• Документација (ова упатство, информации за гаранцијата)

Note: Specific components may vary based on configuration.

Производот завршиview

The HP ProLiant DL360 G9 is a 1U rack-optimized server designed for high-performance computing and data center environments. It features dual Intel Xeon E5-2670 v3 processors, offering robust processing capabilities.

Преден панел

This image displays the front panel of the HP ProLiant DL360 G9 server, highlighting the drive bays, power button, and status indicators. The drive bays are accessible from the front for easy hot-swapping of storage devices.

Заден панел

This image shows the rear panel of the HP ProLiant DL360 G9 server, detailing the various I/O ports, network interfaces, and redundant power supply units. All essential connections for power, network, and peripheral devices are located here.

Поставување

1. Инсталација на решетката

1. Attach the rack rails to the server chassis using the provided hardware.
2. Mount the server into a standard 19-inch server rack, ensuring it is securely fastened.
3. Verify that there is adequate space for airflow around the server.

2. Поврзување за напојување

1. Connect the power cords to the server's power supply units.
2. Plug the other end of the power cords into grounded electrical outlets or a power distribution unit (PDU).
3. Ensure power sources provide 240 Volts as specified.

3. Мрежна врска

1. Connect Ethernet cables from your network infrastructure to the server's network ports.
2. For remote management, connect a dedicated Ethernet cable to the iLO port.

4. Првично стартување

1. Притиснете го копчето за вклучување на предниот панел.
2. Observe the POST (Power-On Self-Test) sequence.
3. Access the BIOS/UEFI setup if necessary to configure boot options or hardware settings.

Упатства за работа

Вклучување/исклучување

• За вклучување: Притиснете го копчето за вклучување на предниот панел.
• За исклучување: Perform a graceful shutdown through the operating system. If unresponsive, press and hold the power button for 5 seconds for a forced shutdown.

Accessing BIOS/UEFI

During the server's boot sequence, press the designated key (typically F9 or Избриши) to enter the BIOS/UEFI setup utility. Refer to the on-screen prompts for the exact key.

Инсталација на оперативен систем

Install your preferred operating system (e.g., Windows Server, Linux) using a bootable USB drive, optical drive, or network installation. Configure RAID arrays as needed before OS installation.

Remote Management (iLO)

The integrated Lights-Out (iLO) port allows for remote management of the server. Access the iLO web интерфејс преку a web browser using the IP address assigned to the iLO port. Default credentials are typically found on a pull-out tag on the server chassis.

Одржување

Чистење

• Regularly clean dust from air vents and fan grilles using compressed air.
• Wipe exterior surfaces with a soft, dry cloth. Do not use liquid cleaners directly on the server.

Ажурирања на фирмверот

Периодично проверувајте ја поддршката на HP website for firmware updates for the BIOS, iLO, and other server components. Apply updates as recommended to ensure optimal performance and security.

Замена на компоненти

For replacing components such as hard drives, memory modules, or power supplies, refer to the specific service manual available on the HP support website. Always power down the server and disconnect power cords before opening the chassis for component replacement.

Решавање проблеми

This section provides solutions for common issues. For more complex problems, consult the HP support webстраница или контактирајте ја техничката поддршка.

• Server does not power on: Check power cord connections, power supply status indicators, and ensure the power button is fully pressed.
• No video output: Verify monitor connection, try a different display cable, or check for POST error codes.
• Operating system fails to boot: Check boot order in BIOS/UEFI, verify hard drive status, or attempt OS repair.
• Overheating warnings: Ensure proper ventilation, clean dust from fans, and check ambient room temperature.
• Проблеми со мрежно поврзување: Verify Ethernet cable connections, check network adapter drivers, and confirm network configuration.

Спецификации

Гаранција и поддршка

This HP ProLiant DL360 G9 server is covered by a standard manufacturer's warranty. For detailed warranty terms and conditions, please refer to the warranty documentation included with your product or visit the official HP support webсајт.

For technical assistance, driver downloads, and additional support resources, please visit the Поддршка на HP Webсајт. When contacting support, please have your server's model number (795236-B21) and serial number readily available.