1. Вовед
This manual provides detailed instructions for the installation, operation, and maintenance of the HOBBYWING XRotor PRO 40A ESC (Dual Pack). This Electronic Speed Controller is designed for multi-rotor applications, offering precise throttle response and compatibility with various flight control systems. Please read this manual thoroughly before use to ensure proper functionality and safety.
2. Информации за безбедност
Важни безбедносни предупредувања:
- Always disconnect the battery before handling or performing maintenance on the ESC or motor.
- Ensure correct polarity when connecting the battery to avoid damage to the ESC and other components.
- Работете со ESC во рамките на неговиот одреден волуменtage and current limits (3-6S Lipo, 40A continuous / 60A peak).
- Држете го ESC подалеку од вода, влага и екстремни температури.
- Монтирајте го ESC на место со соодветен проток на воздух за да спречите прегревање.
- Овој производ не е играчка. Да се чува подалеку од дофат на деца.
3. Содржина на пакетот
Проверете дали сите артикли се присутни во вашиот пакет:
- HOBBYWING XRotor PRO 40A ESC (2 units)
- Упатство за употреба (овој документ)
Image: HOBBYWING XRotor PRO 40A ESC (Dual Pack). This image shows the two ESC units with their pre-attached wires.
4. Поставување и инсталација
Follow these steps for proper installation of the XRotor PRO 40A ESC:
- Монтирање: Securely mount the ESCs to your multi-rotor frame. Ensure adequate ventilation around each ESC to dissipate heat effectively. Use double-sided tape or zip ties as appropriate for your frame.
- Моторна врска: Connect the three motor wires from the ESC to the three wires of your brushless motor. The order of connection determines the motor's rotation direction. If the motor spins in the wrong direction, swap any two of the three motor wires.
- Поврзување за напојување: Connect the red (+) and black (-) power wires of the ESC to your flight battery's corresponding terminals. Ensure correct polarity. The ESC supports 3-6S LiPo batteries.
- Signal Cable Connection: Connect the throttle signal cable (usually a single white or yellow wire) from the ESC to the appropriate channel on your flight controller. The twisted-pair design of the throttle signal cable helps reduce signal interference.
- Initial Calibration (if required by flight controller): Refer to your flight controller's manual for ESC calibration procedures. The XRotor PRO 40A ESC is designed for excellent compatibility and often requires minimal setup.
5. Упатства за работа
The XRotor PRO 40A ESC is largely plug-and-play due to its pre-set configurations. However, understanding its operation is crucial for optimal performance.
- Одговор на гас: The special core program for multi-rotor controllers significantly improves throttle response, providing precise control for flight maneuvers.
- Компатибилност: Optimized software ensures excellent compatibility with disc-type motors and various flight control systems. It supports signal frequencies up to 621Hz. Note that throttle signals over 500Hz are non-standard.
- Време: All settings except "Timing" are pre-set. Adjusting motor timing is typically done via the flight controller or a separate programming card if advanced customization is desired. Refer to your motor's specifications for optimal timing settings.
- DEO Function: The ESC includes a DEO (Driving Efficiency Optimization) function. This can be enabled or disabled, usually through a programming item if available, to further enhance efficiency and response.
6. Одржување
Regular maintenance ensures the longevity and reliable performance of your ESCs:
- Инспекција: Periodically inspect all wires and solder joints for signs of wear, fraying, or corrosion. Repair or replace damaged components immediately.
- Чистење: Keep the ESCs clean and free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning. Avoid using liquids.
- Управување со топлина: Ensure the ESCs are not consistently overheating during operation. If they are, check for adequate airflow, proper motor/propeller combination, and correct timing settings.
- Складирање: When not in use for extended periods, store the ESCs in a dry, cool environment, disconnected from the battery.
7 Смена на проблеми
If you encounter issues with your XRotor PRO 40A ESC, refer to the following common problems and solutions:
| Проблем | Можна причина | Решение |
|---|---|---|
| Motor does not spin or stutters. | Incorrect motor wire connection, ESC not calibrated, faulty motor/ESC. | Check motor wire connections; swap two wires if motor spins wrong way. Perform ESC calibration. Test with a different motor/ESC if possible. |
| ESC gets excessively hot. | Insufficient airflow, overloaded motor, incorrect timing. | Ensure proper ventilation. Check motor/propeller combination for appropriate load. Adjust motor timing if programmable. |
| Intermittent power or signal loss. | Loose connections, damaged wires, signal interference. | Inspect all solder joints and connectors. Ensure signal cable is securely connected and away from power wires. |
| ESC не се вклучува. | Battery not connected, incorrect battery polarity, faulty battery/ESC. | Verify battery connection and polarity. Test battery voltage. Check for visible damage on ESC. |
8. Спецификации
| Карактеристика | Детал |
|---|---|
| Модел | 30902042 |
| Континуирана струја | 40 А |
| Врвна струја | 60 А |
| Влез волуменtage | 3-6S LiPo |
| Тип BEC | Нема БЕЦ |
| Applicable Multicopter Class | 550/650 Class Quadcopter |
| Димензии | 5.25 x 3.5 x 2.25 инчи (Димензии на производот) |
| Тежина на ставката | 5.6 унци |
| Материјал | Алуминиум, пластика |
| UPC | 088718514408 |
9. Гаранција и поддршка
For warranty information and technical support, please contact HOBBYWING North America directly. Details regarding specific warranty periods and conditions are typically provided with the product packaging or on the official HOBBYWING webсајт.
Производител: Технологија на хобивинг
Контакт: Refer to the official HOBBYWING webстраница за најактуелните информации и ресурси за контакт со поддршка.
