Упатство за употреба на SafeWaze FS812 ремен со прилагодлива должина и крстосувач

1. Вовед

This manual provides essential instructions for the proper use, installation, maintenance, and inspection of the SafeWaze FS812 Adjustable Length Cross Arm Strap. This device is designed to serve as a temporary anchorage connector for personal fall arrest systems. It is imperative that all users read and understand these instructions completely before using the product. Failure to follow these instructions can result in serious injury or death.

The SafeWaze FS812 is a critical component of a personal fall arrest system. It must be used in conjunction with other compatible fall protection equipment, including a full-body harness and a connecting device (e.g., lanyard, self-retracting lifeline).

2. Важни безбедносни информации

WARNING: This product is part of a personal fall arrest system. Misuse or failure to follow instructions can result in serious injury or death.

• Only trained and competent persons should use this equipment.
• Inspect the strap before each use for damage, wear, or degradation. Do not use if any defects are found.
• Ensure the anchorage point can support a minimum of 5,000 lbs (22.2 kN) per worker attached, or meet OSHA 1926.502 and ANSI Z359.1 standards.
• Always calculate fall clearance to prevent striking a lower level or obstruction.
• Do not modify the equipment. Repairs must only be performed by the manufacturer or authorized personnel.
• Заштитете го webbing from sharp edges, abrasive surfaces, and high temperatures.
• Never connect multiple lanyards or devices to a single D-ring unless specifically designed for such use.
• In the event of a fall, immediately remove the strap from service and destroy it.

3. Компоненти

The SafeWaze FS812 Adjustable Length Cross Arm Strap consists of the following primary components:

• Webбинг: 1.75 inch (44.45 mm) wide polyester webbing, high-visibility lime green.
• Д-прстени: Two forged steel D-rings, one larger and one smaller, for connection and pass-through.
• Шиење: High-strength polyester stitching securing all components.
• Adjuster: A buckle or similar mechanism for adjusting the strap's length.

Слика 1: The SafeWaze FS812 Adjustable Length Cross Arm Strap. This image displays the lime green polyester webbing with two forged steel D-rings at each end. One D-ring is larger, allowing the other D-ring to pass through it for secure anchorage. An adjustment buckle is visible on one side of the webбинг

4. Поставување и инсталација

The cross arm strap is designed to create a temporary anchorage point around a suitable structural member.

1. Изберете точка за сидро: Identify a structural member (e.g., beam, pipe) that is capable of supporting the required load (minimum 5,000 lbs or 22.2 kN per worker). The anchorage point must be free of sharp edges, burrs, or abrasive surfaces that could damage the webбинг
2. Завиткајте го ременот: Wrap the SafeWaze FS812 strap around the selected structural member.
3. Connect D-Rings: Pass the smaller D-ring through the larger D-ring.
4. Обезбедете ја врската: Pull the smaller D-ring tight against the structural member, ensuring the strap is snug and securely anchored. The larger D-ring should now be accessible for connection to your personal fall arrest system.
5. Adjust Length (if applicable): If the strap features an adjustment mechanism, ensure it is set to the appropriate length to minimize slack and maintain a secure fit around the anchorage.
6. Проверете ја конечната поставка: Visually inspect the entire setup to confirm the strap is correctly installed, free from twists, and not compromised by any hazards.

Важно: The anchorage point must be located above the user's head to minimize fall distance.

5. Упатства за работа

Once the SafeWaze FS812 Cross Arm Strap is securely installed as an anchorage connector:

1. Connect Fall Arrest System: Attach your personal fall arrest system's connecting device (e.g., lanyard, self-retracting lifeline) to the larger D-ring of the cross arm strap.
2. Потврдете ја врската: Ensure the connecting device is properly engaged and locked onto the D-ring.
3. Одржувајте ги празнините: Always be aware of your surroundings and maintain adequate fall clearance below your work area.
4. Редовна инспекција: Periodically check the anchorage connection and the entire fall arrest system during use to ensure continued integrity.

6. Одржување и складирање

6.1 Инспекција

A thorough inspection of the SafeWaze FS812 strap must be performed by the user before each use and by a competent person at least annually.

• Webбинг: Check for cuts, fraying, burns, chemical damage, discoloration, excessive wear, or broken stitches.
• Д-прстени: Inspect for deformation, cracks, corrosion, sharp edges, or any signs of damage. Ensure they pivot freely if designed to do so.
• Шиење: Verify all stitching is intact and free from cuts, breaks, or loose threads.
• Етикети: Ensure all labels are present and legible.
• If any defects are found, immediately remove the strap from service.

6.2 Чистење

Clean the strap with a mild soap and water solution. Rinse thoroughly with clean water and allow to air dry completely in a shaded, well-ventilated area away from direct sunlight or heat. Do not use harsh chemicals, solvents, or abrasive cleaners.

6.3 Складирање

Чувајте го ременот на ладно, суво и чисто место, подалеку од директна сончева светлина, екстремни температури, корозивни хемикалии и остри предмети.

7 Смена на проблеми

Most issues with fall protection equipment relate to improper inspection or installation.

• Strap appears damaged: Do not use. Remove from service immediately.
• D-rings are bent or corroded: Do not use. Remove from service immediately.
• Strap does not fit securely around anchorage: Re-evaluate the chosen anchorage point. Ensure the strap is wrapped and connected correctly, and adjust if possible. If a secure fit cannot be achieved, select a different anchorage point.
• Labels are missing or illegible: Do not use. Remove from service immediately.

If you encounter any issues not covered here, or if you are unsure about the safety or proper use of the product, contact SafeWaze customer support.

8. Спецификации

9. Гаранција и поддршка

For information regarding product warranty, please refer to the official SafeWaze warranty policy available on their webстраницата или директно контактирајте го нивниот оддел за услуги на клиентите.

For technical support, questions about product use, or to report any issues, please contact SafeWaze customer support.

• Производител: SafeWaze
• Webсајт: www.safewaze.com (Прampлинкот, вистинската врска може да варира)
• Контакт: Погледнете ги упатствата на производителот webстраница за тековни информации за контакт.