1. Вовед
The HERTZ H8 DSP is a high-performance digital signal processor designed to optimize the audio experience in automotive sound systems. It provides advanced control over audio signals, allowing for precise equalization, crossover adjustments, time alignment, and other sound tuning functionalities. This manual provides essential information for the proper installation, operation, and maintenance of your H8 DSP unit.
2. Информации за безбедност
Please read and understand all safety instructions before installing or operating the HERTZ H8 DSP. Failure to follow these guidelines may result in injury or damage to the device or vehicle.
- Се препорачува професионална инсталација: Installation should be performed by qualified personnel to ensure proper wiring and system integration.
- Исклучување на струја: Always disconnect the vehicle's battery negative terminal before making any electrical connections to prevent short circuits.
- Правилно поврзување: Ensure all wiring is correctly connected according to the diagrams provided. Incorrect wiring can cause damage to the unit or other components.
- Вентилација: Install the unit in a location that allows for adequate ventilation to prevent overheating.
- Избегнувајте влага: Не го изложувајте уредот на вода или прекумерна влага.
- Безбедно монтирање: Mount the unit securely to prevent it from becoming a projectile in the event of sudden stops or collisions.
- Нивоа на гласност: Продолжената изложеност на високи нивоа на јачина на звук може да предизвика оштетување на слухот. Прилагодете ја јачината на звукот одговорно.
3. Содржина на пакетот
Проверете дали сите елементи се присутни во пакувањето пред да продолжите со инсталацијата:
- HERTZ H8 DSP Processor Unit
- USB кабел
- Спој за напојување/звучник
- Монтажни хардвери (завртки, држачи)
- Упатство за употреба (овој документ)
4. Производот завршиview
The HERTZ H8 DSP unit features a comprehensive layout for inputs, outputs, and control connections. Understanding the physical layout is crucial for proper installation and operation.
Detailed Description of Figure 1:
The image displays the top panel of the HERTZ H8 DSP unit, illustrating its various connection points and controls. From left to right, top to bottom:
- Top Edge (Output Section): Eight RCA output channels are clearly labeled CH1 through CH8, designated as 'OUTPUT'. These are for connecting to external ampказните за слободни животи.
- Left Side (Control & Input Section):
- Порт за компјутер: A USB Type-B port for connecting the DSP to a computer for software configuration.
- DRC Port: For connecting the optional Digital Remote Control (DRC HE) unit.
- ОПТИЧКИ ВО: An optical digital audio input.
- UPGRADE MODE Switch: A toggle switch labeled 'ON | OFF' for firmware upgrades.
- bit Drive Logo: Indicates the proprietary technology used.
- Main Control Panel (Input Level Adjustments):
- Индикатор за напојување: An LED light indicating the unit's power status.
- DE-EQ CHECK Indicator: An LED light related to the De-Equalization function.
- High-Level Input Section (IN level 2-15 V): Features four rotary potentiometers with associated 'CLIP' indicators. These are for adjusting the input sensitivity for high-level (speaker level) signals, labeled 'L - FRONT - R' and 'L - REAR - R'.
- Low-Level Input Section (IN level 0.6-5 V): Contains two rotary potentiometers with 'CLIP' indicators, designed for adjusting the input sensitivity for low-level (RCA) AUX signals, labeled 'L - AUX - R'.
- Bottom Edge (Additional Controls & Inputs):
- SPEAKER TURN ON Switch: A toggle switch labeled 'OFF | ON' for controlling the speaker turn-on function.
- DE-EQ SET: A control or indicator related to the De-Equalization setup.
- UCS: A control or indicator, likely for Universal Control System.
- AUX ВО: Left (L) and Right (R) RCA connectors for auxiliary low-level audio input.
5. Поставување и инсталација
5.1 Системски барања
Софтверски барања
To configure the HERTZ H8 DSP, a personal computer with the following operating system is required:
- Microsoft Windows (32/64 bit): XP, Vista, Windows 7, Windows 8, Windows 10
5.2 Електрични врски
Ensure the vehicle's battery is disconnected before making any connections.
Влез Stagд Врски
- High Level (Speaker): Connect the speaker outputs from your head unit or amplifier to the designated high-level inputs (FL - FR - RL - RR). The input level can be adjusted from 2-15 V using the potentiometers on the unit.
- Low Level (Pre): Connect RCA pre-out signals from your head unit to the low-level inputs.
- AUX ВО: Connect external audio sources via the L/R RCA AUX IN ports. The input level can be adjusted from 0.6-5 V.
Излез Сtagд Врски
- Low Level Pre (default): The H8 DSP provides 8 low-level RCA outputs (CH1-CH8) for connecting to external amplifiers. Default assignments include Front Tweeter L/R, Front Woofer L/R, Rear L/R, Subwoofer, and Center channel. These assignments are configurable via software.
Контролни врски
- From / To Personal Computer: Use the 1 x USB / B port to connect the DSP to your computer for software configuration and tuning.
- DRC HE: Connect the Digital Remote Control (DRC HE) for audio controls and input selection.
- Optical / AUX Select: Use the Optical In / Aux wire control +12V / GND enable for input selection.
- Memory A / Memory B: Use the Memory A / B wire control +12V / GND enable to switch between stored audio presets.
5.3 Физичка инсталација
Select a secure, dry location within the vehicle that is away from direct heat sources and allows for adequate air circulation. Use the provided mounting hardware to firmly secure the H8 DSP unit. Avoid mounting in areas prone to excessive vibration or moisture.
6. Операција
6.1 Почетно вклучување
After all connections are made and verified, reconnect the vehicle's battery. The POWER indicator LED on the H8 DSP unit should illuminate, indicating successful power-up. If the LED does not light, refer to the Troubleshooting section.
6.2 Конфигурација на софтвер
The HERTZ H8 DSP is primarily configured and tuned using dedicated PC software. Connect the DSP to your computer via the USB port. Install the HERTZ DSP control software (available from the manufacturer's website) and follow the on-screen instructions to access and adjust parameters such as:
- Equalization (parametric and graphic)
- Crossover settings (filter type, slope, frequency)
- Порамнување на времето
- Input/Output routing
- Gain adjustments for individual channels
- De-Equalization (DE-EQ) to correct factory head unit processing
6.3 DRC HE Remote Control
If connected, the optional DRC HE remote control allows for convenient adjustments of key functions without needing the PC software. Functions typically include master volume control, input source selection, and switching between stored presets (Memory A/B).
7. Одржување
7.1 Чистење и нега
To maintain the performance and appearance of your H8 DSP, follow these guidelines:
- Избришете го уредот со мека, сува крпа.
- Не користете груби хемикалии, растворувачи или абразивни средства за чистење.
- Ensure the unit remains free of dust and debris, especially around ventilation areas.
7.2 Ажурирања на фирмверот
Periodically check the HERTZ official website for firmware updates. Updates may provide performance enhancements, bug fixes, or new features. Follow the instructions provided with the firmware update package, utilizing the 'UPGRADE MODE' switch on the unit.
8 Смена на проблеми
If you encounter issues with your HERTZ H8 DSP, refer to the following common problems and solutions:
- Без моќност: Check the power and ground connections. Ensure the remote turn-on wire is receiving a +12V signal. Verify the vehicle's fuse.
- Нема аудио излез:
- Verify all input and output RCA cables are securely connected.
- Check input source selection (e.g., AUX, Optical) via software or DRC HE.
- Ensure gain levels are not set to minimum in the software.
- Потврди amplifiers connected to the DSP outputs are powered on and functioning.
- Distorted Audio / Clipping:
- Reduce input sensitivity using the potentiometers on the unit until the 'CLIP' indicator no longer illuminates.
- Lower the source unit's volume.
- Проверете за правилно засилувањеtaging throughout the audio system.
- Cannot Connect to PC Software:
- Ensure the USB cable is securely connected to both the DSP and the computer.
- Verify that the correct USB drivers are installed on your computer.
- Обидете се со друга USB порта или кабел.
- Restart the computer and the DSP unit.
- Noise / Hiss:
- Проверете дали е правилно заземјувањето на сите аудио компоненти.
- Ensure RCA cables are routed away from power cables to prevent interference.
- Adjust gain settings to optimize signal-to-noise ratio.
If the problem persists after attempting these solutions, contact HERTZ customer support or a qualified installer.
9. Спецификации
Технички податоци
- Влез Stage High Level (Speaker): FL - FR - RL - RR AUX IN
- Излез Сtage Low Level (Pre): Front TW L/R, Front WF L/R, Rear L/R, Sub, Center
- Connections From / To Personal Computer: 1 x USB / B
- DRC HE: Audio controls and Memory / Inputs selection
- Optical / AUX Select: Optical In / Aux wire control +12V / GND enable
- Memory A / Memory B: Memory A / B wire control +12V / GND enable
- Барања за софтвер/компјутер: Microsoft Windows (32/64 bit): XP, Vista, Windows 7, Windows 8, Windows 10
- Димензии (Ш x В x Д): 191 x 34 x 131 mm / 7.51” x 1.33” x 4.76”
- Тежина на ставката: Приближно 2.51 килограми
- Ватtage: 120 watts (refer to specific power consumption, not audio output)
10. Информации за гаранцијата
The HERTZ H8 DSP Processor is covered by a manufacturer's warranty. Please refer to the warranty card included with your product or visit the official HERTZ webстраница за детални услови и одредби во врска со гарантното покритие, времетраењето и постапките за побарувања. Зачувајте го доказот за купување за потврда на гаранцијата.
11. Поддршка за корисници
For technical assistance, product inquiries, or support, please contact HERTZ customer service through their official website or authorized distributors. Ensure you have your product model number (H8 DSP) and purchase details available when seeking support.