Упатство за употреба

Вовед

The Palmer POCKET AMP BASS (PEPAMPBASS) is a versatile, portable preamp and effects pedal designed for active and passive bass guitars. It offers extensive sound shaping capabilities, making it suitable for various applications including gigging, recording, and practice. This manual provides detailed instructions for its setup, operation, and maintenance.

Информации за безбедност

• Внимателно прочитајте ги сите упатства пред да ракувате со уредот.
• Не го изложувајте уредот на дожд или влага.
• Обезбедете соодветна вентилација; не блокирајте никакви отвори за вентилација.
• Use only the specified power supply (9V DC, 200mA, center negative).
• Исклучете го напојувањето за време на грмотевици или кога не се користи подолг период.
• Целото сервисирање упатете го на квалификуван сервисен персонал.

Содржина на пакетот

• Палмер ЏЕБ AMP BASS (PEPAMPBASS) unit
• Упатство за употреба (овој документ)
• Note: Power adapter is not included.

Контроли и врски

Преден панел завршиview

Figure 1: Front panel of the Palmer POCKET AMP BASS, highlighting the input and output connections for instrument, headphones, and auxiliary devices.

• Bass In: 1/4" TS input jack for connecting your bass guitar.
• Normal/PAD -12dB Switch: Selects input sensitivity. Use "PAD -12dB" for active basses with high output to prevent clipping.
• Телефони: 1/8" TRS stereo output jack for connecting headphones.
• Помош во: 1/8" TRS stereo input jack for connecting external audio sources like an MP3 player or smartphone for practice.
• Bass Thru: 1/4" TS output jack for sending the unprocessed bass signal directly to another ampладилник или уред.

Контроли на врвните панели

Figure 2: Top panel of the Palmer POCKET AMP BASS, displaying the various knobs and switches for tone shaping and effects.

• MODE Switch (Fuzz, O.DRIVE, CLEAN): Selects the primary sound mode.
  • ЧИСТИ: Provides a transparent, uncolored bass tone.
  • O.DRIVE: Adds a warm, natural overdrive.
  • FUZZ: Delivers a thick, aggressive fuzz effect.
• DRIVE Knob: Adjusts the amount of gain or distortion for the O.DRIVE and FUZZ modes.
• BLEND Knob (Dry/Wet): Mixes the direct (dry) signal with the processed (wet) signal. Fully counter-clockwise is 100% dry, fully clockwise is 100% wet.
• SATURATE Knob: Controls the saturation and compression characteristics of the tone.
• Копче за VOL: Ја прилагодува вкупната излезна јачина на звук на уредот.
• F.SW Switch (MUTE/BYPASS): Controls the footswitch function.
  • МУТИРА: Footswitch mutes the output.
  • БИПАС: Footswitch toggles between active effect and true bypass.
• CAB Switch (FLAT, MODERN, VINTAGД): Selects the cabinet simulation type.
  • РАМЕН: No cabinet simulation, providing a raw, direct sound.
  • МОДЕРНО: Simulates a modern bass cabinet with full-range response.
  • VINTAGE: Offers a warmer, more colored sound reminiscent of classic bass cabinets.
• Копче за БАС: Adjusts the low-frequency response (EQ).
• LEVEL Knob (Mid EQ): Adjusts the gain/cut of the selected mid-frequency.
• FREQ Knob (Mid EQ): Selects the center frequency for the semi-parametric mid-range EQ.
• HIGHS Knob: Adjusts the high-frequency response (EQ).
• Прекинувач за нозе: Engages/disengages the effect or mutes the output, depending on the F.SW setting.

Врски на задниот панел

Figure 3: Rear panel of the Palmer POCKET AMP BASS, detailing the balanced DI output, effects loop, and power input.

• DI Out (Balanced XLR): Балансиран XLR излез за директно поврзување со конзола за миксување или аудио интерфејс.
  • PRE/POST Switch: Determines whether the DI output signal is taken before (PRE) or after (POST) the internal effects and EQ.
  • Прекинувач GND/LIFT: Ground lift switch to eliminate hum caused by ground loops.
• ДО AMP (1/4" TS): Unbalanced 1/4" TS output for connecting to a bass ampживописен.
• FX Insert (1/4" TRS): Stereo 1/4" TRS jack for connecting external effects pedals in a send/return loop. Tip is Send, Ring is Return.
• DC 9V (200mA, Center Negative): Power input jack for a 9V DC power adapter.

Поставување

1. Поврзување за напојување: Connect a 9V DC, 200mA, center negative power adapter (not included) to the "DC 9V" input on the rear panel. Alternatively, the unit can be powered by a 9V battery (located in the compartment on the bottom).
2. Поврзување на инструменти: Plug your bass guitar into the "Bass In" jack on the front panel. If using an active bass with high output, set the "Normal/PAD -12dB" switch to "PAD -12dB".
3. Излезна врска:
   • For headphones: Connect headphones to the "Phones" jack.
   • За еден amplifier: Connect the "TO AMP" jack to your bass ampвлез на лифиерот.
   • For a mixing console/audio interface: Connect the "DI Out" XLR to the console/interface. Adjust the "PRE/POST" and "GND/LIFT" switches as needed.
4. Помошен влез: To play along with external audio, connect your audio source (e.g., smartphone) to the "Aux In" jack. The volume of the auxiliary input is controlled by the source device.
5. Effects Loop (Optional): To integrate external effects, connect a TRS cable from the "FX Insert" jack to your effects pedal(s). The Tip of the TRS cable is the Send, and the Ring is the Return.

Упатства за работа

The Palmer POCKET AMP BASS offers a range of controls to shape your bass tone. Experiment with the settings to find your desired sound.

Sound Modes and Drive

• Користете го РЕЖИМ switch to select between CLEAN, O.DRIVE, and FUZZ.
• Прилагодете го ВОЗЕТЕ knob to control the intensity of the overdrive or fuzz effect. Start with lower settings and increase gradually.
• На ЗАСИТЕНИ knob adds harmonic richness and compression. Higher settings will increase sustain and density.
• На БЛЕНДИРАЈ knob allows you to mix your original clean bass signal with the processed signal. This is particularly useful for retaining low-end clarity when using distortion effects.

Изедначување (EQ)

• На BASS knob boosts or cuts low frequencies.
• На ВИСОКИ knob boosts or cuts high frequencies.
• The mid-range EQ is semi-parametric:
  • Користете го ФРЕК knob to select the specific mid-frequency you wish to adjust.
  • Користете го НИВО knob to boost or cut the selected mid-frequency.

Cabinet Simulation

• На CAB switch allows you to select between three different cabinet simulations:
  • РАМЕН: Bypasses cabinet simulation.
  • МОДЕРНО: Provides a clear, full-range sound typical of modern bass cabinets.
  • VINTAGE: Offers a warmer, more colored sound reminiscent of classic bass cabinets.

Footswitch Functionality

• Поставете го F.SW switch to either MUTE or BYPASS to define the footswitch's action.
• Press the footswitch to activate the selected function.

Одржување

• Чистете го уредот со мека, сува крпа. Не користете абразивни средства за чистење или растворувачи.
• Избегнувајте изложување на уредот на екстремни температури, влажност или директна сончева светлина.
• When not in use for extended periods, remove the 9V battery to prevent leakage.

Решавање проблеми

Спецификации

Гаранција и поддршка

For warranty information and technical support, please refer to the official Palmer webлокација или контактирајте го вашиот локален продавач. Зачувајте го доказот за купување за какви било гаранциски побарувања.

За дополнителна помош, можете да ја посетите Palmer Store on Amazon.