GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Вовед

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Информации за безбедност

ПРЕДУПРЕДУВАЊЕ: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Пред инсталацијата, проверете дали напојувањето е ИСКЛУЧЕНО на прекинувачот.
• Овој уред е наменет за инсталација во согласност со Националниот код за електрична енергија и локалните прописи.
• Do not use in wet locations or where directly exposed to water.
• Само за внатрешна употреба.

Содржина на пакетот

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Завртки за монтирање
• Wire Nuts (may vary by package)
• Упатство за употреба (овој документ)

Поставување и инсталација

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Исклучете го напојувањето: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Отстранете го стариот прекинувач: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Идентификувајте ги жиците:
   • Линија (жешка): Usually black, coming from the circuit breaker.
   • Вчитај: Usually black, going to the light fixture or appliance.
   • Неутрално: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Терен: Usually green or bare copper.
4. Поврзете нов прекинувач: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Поврзете го Линија wire to the terminal marked "LINE".
   • Поврзете го Вчитај wire to the terminal marked "LOAD".
   • Поврзете го Неутрален wire to the terminal marked "NEUTRAL".
   • Поврзете го Земјата wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Монтирање на прекинувач: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Инсталирајте ѕидна плоча: Прикачете ја новата или постоечката ѕидна плоча.
7. Вратете ја моќноста: Вклучете го напојувањето повторно на прекинувачот.

Слика 1: Предна страна view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Вклучување на Z-Wave (Спарување)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle еднаш. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Ракување со прекинувачот

Рачна контрола

• Притиснете го врвот of the paddle to turn the connected load ON.
• Притиснете го дното of the paddle to turn the connected load ИСКЛУЧЕНО.

Контрола на Z-бранот

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Одржување

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Чистење: За да го исчистите прекинувачот, избришете го со мека, дamp крпа. Не користете абразивни средства за чистење или растворувачи.
• Ажурирања на фирмверот: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Општа нега: Осигурајте се дека прекинувачот не е изложен на прекумерна влага или екстремни температури.

Решавање проблеми

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle еднаш. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Спецификации

Гаранција и поддршка

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webсајт или контактирајте со нивниот оддел за услуги на клиентите.

Webсајт: www.gocontrol.com

Производител: GOCONTROL