1. Вовед
This manual provides detailed instructions for the installation, operation, and maintenance of the CDVI 433MHz Radio Keypad (Digicode) and its associated SEL2641R433NN 1-Relay 12V Receiver. This system is designed for secure access control applications.
Ве молиме внимателно прочитајте го ова упатство пред да се обидете со каква било инсталација или работа за да обезбедите правилна функционалност и безбедност.
Figure 1: CDVI 433MHz Radio Keypad and SEL2641R433NN Receiver. The image shows the silver-colored keypad with illuminated blue numbers (0-9, A, B, C) and a transparent plastic receiver unit.
2. Информации за безбедност
- Пред инсталација или одржување, осигурајте се дека целата струја е исклучена.
- Инсталирањето треба да го врши само квалификуван персонал.
- Do not expose the keypad or receiver to extreme temperatures, moisture, or direct sunlight.
- Use only specified power supply (12V).
- Да се чува подалеку од дофат на деца.
3. Поставување и инсталација
3.1. Компоненти надview
The system consists of two main components:
- Radio Keypad (Digicode): The input device for entering access codes.
- SEL2641R433NN Receiver: The unit that receives signals from the keypad and controls the access mechanism (e.g., door lock).
3.2. Монтирање на тастатурата
- Choose a suitable mounting location, typically near the access point, ensuring it is protected from direct weather exposure if outdoors.
- Mark the drilling points using the keypad's mounting plate as a template.
- Дупчете дупки и вметнете соодветни ѕидни приклучоци.
- Прицврстете ја монтажната плоча на ѕидот.
- Attach the keypad securely to the mounting plate.
3.3. Поврзување на приемникот
The SEL2641R433NN receiver requires a 12V power supply and connection to the access control device. Refer to the wiring diagram below for typical connections.
- Влез на енергија: Connect 12V DC to the designated terminals. Observe polarity.
- Излез на реле: The receiver has one relay. Connect the Normally Open (NO) or Normally Closed (NC) contacts to your access control device (e.g., electric strike, magnetic lock) as required.
(Note: A detailed wiring diagram is typically provided with the physical product. Consult it for specific terminal assignments.)
4. Упатства за работа
4.1. Првично вклучување
Once the receiver is wired and powered, it will enter a standby mode. The keypad will illuminate when a button is pressed.
4.2. Programming Access Codes
The keypad and receiver must be paired, and access codes programmed. This process typically involves:
- Влегување во режим на програмирање: This usually involves a master code or a physical button on the receiver.
- Adding New Codes: Follow the specific sequence to input new user codes (e.g., Master Code + * + New Code + #).
- Deleting Codes: Follow the specific sequence to remove existing user codes.
- Излегување од режимот на програмирање: Save changes and exit programming mode.
(Note: Refer to the specific programming instructions provided with your product for exact key sequences and procedures, as these can vary by firmware version.)
4.3. Одобрување на пристап
To grant access, simply enter a valid programmed code on the keypad. Upon successful code entry, the receiver's relay will activate for a pre-set duration, unlocking the connected device.
5. Одржување
- Чистење: Исчистете ја површината на тастатурата со мека, дamp крпа. Не користете абразивни средства за чистење или растворувачи.
- Редовни проверки: Periodically check all wiring connections for security and integrity, especially for the receiver unit.
- Управување со кодови: Редовно повторноview and update access codes for security purposes. Delete codes of former users.
6 Смена на проблеми
| Проблем | Можна причина | Решение |
|---|---|---|
| Тастатурата не реагира. | No power to receiver or keypad not paired. | Check 12V power supply to receiver. Ensure keypad is correctly paired with the receiver. |
| Access code not working. | Incorrect code entered, code not programmed, or keypad/receiver not paired. | Verify code. Re-program code. Re-pair keypad and receiver. |
| Door/lock not activating. | Incorrect wiring to lock, faulty lock, or relay issue. | Check wiring connections. Test the lock mechanism independently. Consult a technician if relay is suspected faulty. |
| Short range or intermittent operation. | Radio interference or receiver antenna issue. | Check for sources of radio interference. Ensure receiver antenna is unobstructed. |
7. Спецификации
| Карактеристика | Детал |
|---|---|
| Броеви на модели | SEL2641R433NN, GALEOR1R, F1002000052 |
| Фреквенција | 433 MHz |
| Ресивер Напојување | 12V DC |
| Излез на реле | 1 Relay (NO/NC contacts) |
| Тип на тастатура | Радио (безжично) |
| ASIN | B06VWH6V57 |
8. Гаранција и поддршка
Information regarding product warranty is typically provided with the purchase documentation or can be found on the manufacturer's official webстраница. Ве молиме задржете го доказот за купување за гаранциски барања.
For technical support or further assistance, please contact CDVI customer service or your authorized dealer. Contact details can usually be found on the CDVI webсајт (www.cdvi.com).
