1. Производот завршиview
The Bside CCT01 Digital Coating Thickness Gauge is designed for non-destructive, fast, and precise measurement of coating thickness. It operates based on either the magnetic induction principle (F probe) or the eddy current principle (N probe), depending on the substrate material. This device is equipped with both internal F and N probes.
The F probe is suitable for measuring non-magnetic coatings such as aluminum, chrome, copper, zinc, paint, varnish, enamel, and rubber on iron or steel substrates. It is also applicable to alloyed and hardened magnetic steel, but not austenitic steel.
The N probe is used for insulating coatings like paint, anodizing, and ceramics on all non-ferrous metals (e.g., aluminum, copper, zinc die casting, brass) and on austenitic stainless steels.
Слика 1: Предна страна view of the Bside CCT01 Digital Coating Thickness Gauge, showing the LCD display, control buttons, and the Bside CCT01 branding.
2. Клучни карактеристики
- Прикажи: 128x128 dot matrix LCD with standard menu operations.
- Режими на мерење: Supports both single and continuous measurement.
- Group Modes: Two group modes: Direct (DIR) and General (GEN). Readings in Direct mode are lost upon power off, while General mode stores up to 80 readings per group.
- Калибрација: Zero-point calibration and multi-point calibration (up to 4 points) for each group.
- Управување со податоци: Ability to recall, delete specified readings, or delete entire group readings.
- Статистика: Displays mean, minimum, maximum, and standard deviation of readings.
- Probe Modes: Auto, Magnetic (F), and Eddy Current (N) probe selection.
- Функција за аларм: User-definable high or low limit alarms for each group.
- Моќен менаџмент: Функција за автоматско исклучување.
- Поврзување: USB interface for data transmission to a computer.
- Индикатори: Low battery and error indications.
3. Поставување
3.1 Инсталација на батерија
- Пронајдете ја преградата за батерии на задната страна на уредот.
- Using a small screwdriver, remove the screws securing the battery compartment cover.
- Insert two 1.5V AAA batteries, ensuring correct polarity as indicated inside the compartment.
- Вратете го капакот на преградата за батерии и прицврстете го со завртки.
Слика 2: View of the battery compartment, showing the placement for two 1.5V AAA batteries.
Слика 3: Заден дел view of the device, displaying the battery compartment cover and a warning regarding battery disposal and recycling.
3.2 Вклучување/исклучување
- За да го вклучите, притиснете и задржете го Моќ копче.
- Уредот автоматски ќе се исклучи по одреден период на неактивност за да се заштеди траење на батеријата.
4. Упатства за работа
4.1 Режими на мерење
- Единечен режим: For individual measurements. Press the probe onto the surface, read the value, then lift.
- Континуиран режим: For scanning a surface. Keep the probe on the surface and slide it to take multiple readings.
4.2 Group Modes
- Direct (DIR) Group: Readings are displayed but not stored in memory. Data is lost when the device powers off.
- General (GEN) Group: Readings are automatically stored. Up to 80 readings can be stored for each of the four general groups. Each group maintains individual statistics, alarm limits, and calibration settings.
4.3 Калибрација
Accurate measurements require proper calibration. The device supports zero-point and multi-point calibration.
- Калибрација на нулта точка: Used to set the zero reference on an uncoated substrate.
- Multi-Point Calibration (up to 4 points): For enhanced accuracy across the measurement range, using calibration foils of known thickness.
Refer to the on-screen menu for detailed calibration steps.
4.4 Probe Modes
The device can automatically detect the substrate type or be manually set.
- Автоматски режим: The gauge automatically selects between F (magnetic induction) and N (eddy current) probe principles.
- Magnetic Mode (F Probe): For non-magnetic coatings on ferrous substrates.
- Eddy Current Mode (N Probe): For insulating coatings on non-ferrous substrates.
Слика 4: Одблиску view of the professional test probe at the bottom of the device, designed for accurate contact with the measurement surface.
4.5 Поставување аларми
Users can set high and low alarm limits for each group. An alarm icon will be displayed on the LCD when a reading exceeds these limits.
4.6 Data Management and Statistics
Navigate through the menu to:
- Потсетиме: View зачувани отчитувања.
- Избриши: Remove specific readings or clear an entire group.
- Browse Statistics: View calculated statistics including the number of readings, mean, minimum, maximum, and standard deviation for the current group.
5. Пренос на податоци
The Bside CCT01 features a USB interface for transferring measurement data to a computer. This allows for further analysis and record-keeping.
Слика 5: Одблиску view of the USB interface located on the side of the device, used for data transmission.
6. Одржување
6.1 Замена на батеријата
When the low battery indicator appears, replace the AAA batteries as described in Section 3.1. Always use fresh batteries for optimal performance.
6.2 Чистење
Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the probe tip clean and free of debris for accurate readings.
6.3 Складирање
Store the device in its original packaging or a protective case when not in use. Avoid extreme temperatures and high humidity. If storing for extended periods, remove the batteries to prevent leakage.
7 Смена на проблеми
- Индикација за слаба батерија: If the low battery icon appears, replace the batteries immediately.
- Индикација за грешка: If an error message is displayed, refer to the device's on-screen help or power cycle the device. If the issue persists, contact customer support.
- Неточни читања: Ensure the probe tip is clean, the device is properly calibrated, and the correct probe mode (F/N/Auto) is selected for the substrate.
8. Спецификации
| Параметар | F Probe (Magnetic Induction) | N Probe (Eddy Currents) |
|---|---|---|
| Мерен опсег | 0 to 1300um (0 to 51.2mils) | 0 to 1300um (0 to 51.2mils) |
| Точност | (3% + 2um) / (3% + 0.078mils) | (3% + 2um) / (3% + 0.078mils) |
| Резолуција | 0-999um (1um), 1000-1300um (0.01mm) 0-39.39mils (0.01mils), 39.4-51.2mils (0.1mils) | 0-999um (1um), 1000-1300um (0.01mm) 0-39.39mils (0.01mils), 39.4-51.2mils (0.1mils) |
| Калибрација | One-point to four-point calibration, zero-point calibration | |
| Data Groups | One direct group (readings not stored), Four general groups (readings stored automatically) | |
| Статистика | Number of readings, mean, minimum, maximum, standard deviation | |
| Единици | мм, мм, милс | |
| Аларм | User-settable high/low alarm limits | |
| Минимален радиус на закривеност (конвексен) | 1.5 мм | |
| Минимален радиус на закривеност (конкавен) | 25 мм | |
| Minimum Measuring Area Diameter | 6 мм | |
| Минимална дебелина на подлогата | 0.5 мм (0.02") | 0.3 мм (0.012") |
| Maximum Measuring Rate | Две читања во секунда | |
| Компјутерски интерфејс | USB | |
| Напојување | Two 1.5V AAA batteries (not included) | |
| Опкружување за работа | Temperature: 0 to 40°C (32 to 104°F); Humidity: 20% to 90% RH | |
| Складирање на животната средина | Температура: -20 до 70°C (-4 до 158°F) | |
| Стандардна усогласеност | ROHS, WEEE | |
| Димензии | 110mm x 53mm x 24mm (4.33" x 2.09" x 0.94") | |
| Материјал на случајот | ABS | |
| Тежина | 92 g (3.24 oz) | |
9. Содржина на пакетот
Стандардниот пакет вклучува:
- Bside CCT01 Digital Coating Thickness Gauge
- USB кабел
- Фолии за калибрација
- Substrate Plates (Ferrous and Non-Ferrous)
- Упатство за употреба
Figure 6: The Bside CCT01 gauge shown with its included accessories, including calibration foils and a USB cable, on a car panel.
10. Гаранција и поддршка
Information regarding product warranty and customer support is typically provided with the purchase documentation or available on the manufacturer's official website. Please refer to those resources for details on warranty coverage, technical assistance, and service options.
