1. Вовед
This manual provides essential instructions for the proper installation, operation, and maintenance of the Norlake 139850S Dixel XR06 Programmed Controller. This device is designed for precise temperature control in commercial refrigeration applications. Please read this manual thoroughly before attempting to install or operate the controller to ensure safe and efficient performance.
2. Информации за безбедност
- Always disconnect power before performing any installation, wiring, or maintenance procedures.
- Installation and wiring should only be performed by qualified personnel in accordance with local and national electrical codes.
- Обезбедете ја јачината на напојувањетоtage matches the controller's specifications (120V, 50-60Hz).
- Не го изложувајте контролерот на вода или прекумерна влажност.
- Користете оригинални OEM делови за безбедност, сигурност и перформанси.
3. Производот завршиview
The Norlake 139850S Dixel XR06 is a compact, programmed controller designed for refrigeration units. It features a digital display for temperature readings and status indicators, along with control buttons for setting parameters. The unit is supplied with a removable terminal block for electrical connections and mounting clips for secure installation.
Слика 1: Norlake 139850S Dixel XR06 Programmed Controller. This image displays the Norlake 139850S Dixel XR06 Programmed Controller unit, a green terminal block connector, and two white mounting clips. The controller features a digital display and control buttons on the front panel, with wiring diagrams and specifications printed on its side.
Компоненти на контролерот:
- Дигитален екран: Ја прикажува моменталната температура и работниот статус.
- Контролни копчиња: Used for setting parameters and navigating menus (e.g., SET, Up, Down, Light/Aux).
- Терминален блок: Removable connector for electrical wiring.
- Клипови за монтирање: For securing the controller in a panel cutout.
- Идентификациона ознака: Located on the side, indicating model, voltage, frequency, probe type (NTC), and power consumption (3.3VA MAX).
4. Поставување и инсталација
4.1 Монтирање
- Create a panel cutout of appropriate dimensions for the controller.
- Вметнете го контролерот во отворот од напред.
- Secure the controller using the provided mounting clips, ensuring a snug fit.
4.2 Wици
Refer to the wiring diagram printed on the side of the controller and the specific requirements of your refrigeration system. The terminal block connections typically include:
- Power Supply (120V, 50-60Hz): Connect to the designated 'Supply' terminals.
- Compressor (Comp): Connect to the compressor load terminals.
- Фан: Connect to the fan load terminals.
- Defrost (Def): Connect to the defrost heater terminals.
- Probe (NTC): Connect the temperature sensor probe to the designated NTC probe terminals.
Забелешка: Ensure all connections are secure and correctly polarized. Incorrect wiring can damage the unit or pose a safety hazard.
5. Упатства за работа
5.1 Почетно вклучување
Once wired and mounted, apply power to the controller. The display will illuminate, showing the current temperature measured by the NTC probe.
5.2 Setting the Temperature (Set Point)
- Притиснете го ПОСТАВЕТЕ button. The current set point temperature will flash on the display.
- Користете го Up и Долу arrow buttons to adjust the set point to the desired temperature.
- Притиснете го ПОСТАВЕТЕ button again to confirm and save the new set point. The display will return to showing the current temperature.
5.3 Accessing Parameters (Hot Key)
Advanced parameters, such as defrost cycles, differential, and probe calibration, can be accessed through a specific sequence, often referred to as the 'Hot Key' function. Consult the detailed Dixel XR06 programming manual for specific parameter codes and adjustment procedures. This typically involves holding down certain buttons for a few seconds to enter the parameter menu.
6. Одржување
6.1 Чистење
- Wipe the controller's front panel with a soft, damp крпа.
- Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the display or internal components.
6.2 Инспекција
- Периодично проверувајте ги поврзувањата на жиците за затегнатост и знаци на абење или корозија.
- Ensure the temperature probe is securely in place and free from damage.
7 Смена на проблеми
This section addresses common issues you might encounter with the controller.
| Проблем | Можна причина | Решение |
|---|---|---|
| Controller display is off | Нема напојување; лабави жици | Check power connections and circuit breaker. Ensure wiring is secure. |
| Неправилно отчитување на температурата | Faulty probe; probe not properly installed | Check probe connection. Replace probe if damaged. Verify probe type (NTC). |
| Compressor/Fan not operating | Incorrect set point; wiring issue; controller fault | Verify set point. Check wiring to compressor/fan. Consult a qualified technician if fault persists. |
| Код за грешка на екранот | Специфична системска грешка | Refer to the Dixel XR06 programming manual for specific error code definitions and troubleshooting steps. |
8. Спецификации
- Број на модел: 139850S
- Бренд: Норлејк
- Тип на контролор: Programmed Controller (Dixel XR06)
- Voltage: 120V
- Фреквенција: 50-60 Hz
- Тип на сонда: NTC
- Потрошувачка на енергија: 3.3VA MAX
- Работна влажност: 20-85% RH (некондензирачки)
- Approximate Unit Dimensions (based on package): 10 x 10 x 8 инчи
- Приближна тежина на предметот: 8 унци
- UPC: 046843096626
- Производител: Норлејк
- Прво достапен датум: 10 октомври 2017 година
9. Гаранција и поддршка
The Norlake 139850S Dixel XR06 Programmed Controller is a genuine OEM (Original Equipment Manufacturer) replacement part. For specific warranty information, please refer to the terms provided by Norlake or your authorized distributor at the time of purchase. For technical support or service, contact your Norlake dealer or a qualified refrigeration technician.
