Вовед
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Skytech 9800325 SKY-3301P2 remote control system. This system is designed to offer safe, reliable, and user-friendly control for gas heating appliances. It supports both thermostatic and manual operation from the transmitter.
The system utilizes radio frequencies (RF) for communication within a 20-foot range, employing non-directional signals. Each system operates on one of 1,048,567 security codes, pre-programmed at the factory. It is essential to match the remote receiver's code to that of the transmitter before initial use.
Содржина на пакетот
Upon unpacking, verify that all components are present and undamaged. The package should include:
- Transmitter (Remote Control Unit)
- Единица за приемник
- Wall Holder for Transmitter
- Ѕидна плоча
- Инструкции за инсталација
- Batteries (2 AAA for transmitter, 4 AA for receiver)
Слика 1: Во текот наview of the Skytech 9800325 SKY-3301P2 remote control system, showing the handheld transmitter, the wall-mounted receiver, and the wired receiver box.
Поставување и инсталација
1. Инсталација на батерија
Предавател: Open the battery compartment on the back of the transmitter and insert two (2) AAA batteries, observing the correct polarity. Close the compartment securely.
Приемник: Open the battery compartment on the receiver unit and insert four (4) AA batteries, observing the correct polarity. Close the compartment securely.
2. Receiver Placement and Wiring
The receiver can be installed in the wall, on the hearth, or under the fireplace behind the control access panel. Ensure the receiver is placed in a location that allows for proper signal reception from the transmitter and is not exposed to excessive heat.
Connect the two wires from the receiver to the appropriate terminals on your gas heating appliance's control valve. Refer to your appliance's manual for specific wiring instructions. Ensure all connections are secure and properly insulated.
Слика 2: Close-up of the receiver unit, showing the 'OFF', 'REMOTE', 'ON' slider switch and 'LEARN' button. This unit connects to the fireplace.
3. Matching Security Codes (Learning Function)
The transmitter and receiver are factory-matched. However, if they lose synchronization or if you are replacing a component, you may need to re-match them:
- Ensure batteries are installed in both the transmitter and receiver.
- Locate the 'LEARN' button on the receiver unit.
- Press and hold the 'LEARN' button on the receiver until you hear a series of beeps (approximately 1-2 seconds).
- Within 10 seconds, press any button on the transmitter. The receiver will emit another series of beeps, confirming that the codes have been matched.
If the matching process fails, repeat the steps. Ensure the transmitter is within 20 feet of the receiver during this process.
Упатства за работа
Контроли на предавателот
Слика 3: Close-up of the handheld transmitter, showing the backlit LCD display with room temperature and set temperature, and the 'DOWN', 'MODE', 'UP' buttons. The flip cover conceals 'PROG' and 'SET' buttons.
- Копче UP: Increases temperature setting or navigates menu options.
- ДОЛЕ копче: Decreases temperature setting or navigates menu options.
- Копче MODE: Cycles through operating modes (ON, THERMO, OFF, PROGRAM).
- PROG Button (under flip cover): Used for programming thermostat schedules.
- SET Button (under flip cover): Used to confirm settings or enter programming mode.
Receiver Slider Switch
The receiver unit has a three-position slider switch:
- НА: Manually turns the appliance ON, bypassing remote control.
- ДАЛЕЧИНСКИ УПРАВУВАЧ: Allows the appliance to be controlled by the transmitter.
- ИСКЛУЧЕНО: Manually turns the appliance OFF, bypassing remote control.
For normal operation with the remote control, ensure the receiver switch is set to ДАЛЕЧИНСКИ.
Работни режими
Притиснете го РЕЖИМ button on the transmitter to cycle through the following modes:
- НА: The appliance will turn on and remain on until switched off.
- ТЕРМО: The appliance will operate based on the set temperature. When the room temperature falls below the set temperature, the appliance will turn on. When the room temperature rises above the set temperature, the appliance will turn off.
- ИСКЛУЧЕНО: The appliance will remain off.
- ПРОГРАМА: The appliance will follow the programmed schedule for temperature control.
Setting the Temperature (THERMO Mode)
- Притиснете го РЕЖИМ button until "THERMO" is displayed on the LCD.
- Користете го UP or ДОЛУ buttons to adjust the desired set temperature. The display will show both the current room temperature and the set temperature.
Programming a Schedule (PROGRAM Mode)
The 3301P2 allows for programmable temperature settings. Lift the flip cover on the transmitter to access the ПРОГ и ПОСТАВЕТЕ копчиња.
- Притиснете го РЕЖИМ button until "PROGRAM" is displayed on the LCD.
- Притиснете го ПРОГ копче за да влезете во режим на програмирање.
- Користете го UP or ДОЛУ buttons to adjust the time and temperature settings for each program period (P1, P2).
- Притиснете ПОСТАВЕТЕ за да потврдите секое поставување и да преминете на следното.
- The system typically allows for two program periods (P1 for morning/day, P2 for evening/night) with separate ON/OFF times and temperatures. Consult the detailed instructions provided with the product for specific programming steps, as these can be intricate.
Забелешка: The programming interface may require careful attention to detail. If you encounter difficulties, refer to the troubleshooting section or contact support.
Одржување
Замена на батеријата
Replace batteries in both the transmitter and receiver when the low battery indicator appears on the transmitter's LCD, or if the remote control range decreases significantly. Use high-quality alkaline batteries for optimal performance.
- Предавател: 2 x AAA батерии.
- Приемник: 4 x AA батерии.
Always replace all batteries at the same time. Dispose of old batteries responsibly according to local regulations.
Чистење
Избришете го предавателот и приемникот со мека, сува крпа. Не користете абразивни средства за чистење и не ги потопувајте уредите во вода.
Решавање проблеми
| Проблем | Можна причина | Решение |
|---|---|---|
| Далечинскиот управувач не реагира. |
|
|
| Appliance does not turn on/off in THERMO mode. |
|
|
| LCD екранот е затемнет или празен. | Low batteries in the transmitter. | Replace AAA batteries in the transmitter. |
Спецификации
- Модел: 9800325 (SKY-3301P2)
- Бренд: СкајТек
- Димензии на производот: 6.5 x 3.6 x 3 inches (Transmitter and Receiver combined, approximate)
- Тежина: 12.96 унци (приближно)
- Моќност на предавателот: 2 x AAA батерии
- Моќност на ресиверот: 4 x AA батерии
- Тип на контрола: Притиснете го копчето
- Специјална карактеристика: Programmable Thermostat, Backlit Display
- Безжичен опсег: До 20 стапки (ненасочен RF)
- Безбедносни кодови: 1,048,567 unique codes
- Специфична употреба: Fireplace Control, Thermostat Control, Indoor Residential Environments
Гаранција и поддршка
For warranty information or technical support, please refer to the documentation included with your purchase or visit the official SkyTech webстраница. Зачувајте го доказот за купување за гаранциски побарувања.
Производител: Skytech
For further assistance, contact SkyTech customer service.
