1. Вовед
The ANYCUBIC Wash and Cure 3.0 is an upgraded 2-in-1 wash and cure station designed for resin 3D printer models. It features a larger cleaning capacity, innovative gooseneck lights for uniform curing, a dual-layer design for IPA saving, and quiet, simple operation. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance and longevity of your device.
2. Инструкции за безбедност
- Always wear protective gloves and eye protection when handling resin or cleaning solutions.
- Ensure adequate ventilation in your workspace to avoid inhaling resin fumes.
- Чувајте го уредот подалеку од деца и домашни миленици.
- Не го изложувајте уредот на директна сончева светлина или високи температури.
- Use only recommended cleaning solutions (e.g., Isopropyl Alcohol - IPA) and follow their safety guidelines.
- Never operate the curing function without the UV-blocking top cover in place.
- Исклучете го напојувањето пред чистење или вршење на одржување.
3. Што има во кутијата
Upon unboxing your ANYCUBIC Wash and Cure 3.0, please verify that all components are present:
- Wash and Cure Machine Unit
- Washing Bucket (4L capacity)
- Корпа за перење
- Rack Bar (4 pcs)
- Curing Table
- Светло со гуски грло
- Комплет со хексадецимален клуч
- Упатство за употреба
- Адаптер за напојување
Слика 3.1: All components included in the ANYCUBIC Wash and Cure 3.0 package.
4. Водич за поставување
- Отпакувај: Внимателно отстранете ги сите компоненти од пакувањето.
- Поставување: Place the main unit on a stable, level surface in a well-ventilated area.
- Поврзување за напојување: Connect the power adapter to the unit and then to a power outlet.
- Gooseneck Light Installation: Insert the gooseneck light into its designated port on the main unit.
- Washing Bucket Preparation:
- For washing, place the washing basket inside the washing bucket.
- Fill the washing bucket with your chosen cleaning solution (e.g., IPA) up to the appropriate level, ensuring it covers the models to be cleaned.
- Curing Table Preparation: For curing, ensure the curing table is placed on the rotating platform.
Видео 4.1: Официјално завршеноview of the Wash and Cure 3.0, demonstrating its features and basic setup.
5. Упатства за работа
5.1. Washing Mode
- Prepare Models: Remove printed models from the build plate. For models still on the build plate, use the hanging cleaning mode. For detached models, place them in the washing basket.
- Place Washing Bucket: Position the washing bucket with the models and cleaning solution onto the main unit's platform. Ensure the UV-blocking cover is in place.
- Изберете режим на перење: Press the "Wash" button on the control panel.
- Поставете време: Use the rotary knob to set the desired washing time (typically 1-30 minutes, refer to resin manufacturer guidelines).
- Започнете со перење: Press the Start/Stop button to begin the washing cycle. The internal propeller will agitate the cleaning solution.
- Завршување: The machine will beep when the cycle is complete. Carefully remove the models and allow them to dry.
Слика 5.1: Dual cleaning modes for models on a build plate (hanging) or detached (basket).
Видео 5.1: Demonstration of the washing process in the ANYCUBIC Wash and Cure 2.0 machine, which shares similar washing mechanisms with the 3.0 model.
5.2. Curing Mode
- Place Models: After washing and drying, place the models on the curing table.
- Position Curing Table: Place the curing table with models onto the main unit's rotating platform. Ensure the UV-blocking cover is in place.
- Select Cure Mode: Press the "Cure" button on the control panel.
- Поставете време: Use the rotary knob to set the desired curing time (typically 1-30 minutes, refer to resin manufacturer guidelines).
- Activate Gooseneck Light (Optional): Press the "FlexiCure" button to activate the gooseneck light for targeted curing of complex areas.
- Start Curing: Press the Start/Stop button to begin the curing cycle. The platform will rotate, and UV lights will activate.
- Завршување: The machine will beep when the cycle is complete. Remove the fully cured models.
Слика 5.2: The gooseneck light provides localized strengthening and uniform curing for intricate details on 3D models.
Видео 5.2: A user demonstrating the curing process with the ANYCUBIC Wash and Cure station, highlighting its ease of use.
6. Одржување
- Cleaning the Washing Bucket: Regularly clean the washing bucket and basket to prevent resin buildup. Dispose of used cleaning solution responsibly according to local regulations.
- Чистење на единицата: Wipe down the exterior of the unit with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- UV Light Maintenance: Keep the UV lights and gooseneck light clean and free of dust or resin residue to ensure optimal curing performance.
- Складирање: When not in use, store the unit in a cool, dry place away from direct sunlight.
7 Смена на проблеми
| Проблем | Можна причина | Решение |
|---|---|---|
| Уредот не се вклучува. | Кабелот за напојување не е поврзан; проблем со штекерот. | Проверете го поврзувањето на кабелот за напојување; обидете се со друг штекер. |
| Washing/Curing cycle does not start. | Top cover not properly closed; mode not selected. | Ensure the UV-blocking cover is securely in place; select desired mode (Wash/Cure). |
| Models are not clean after washing. | Insufficient washing time; dirty cleaning solution; incorrect IPA concentration. | Increase washing time; replace cleaning solution; ensure proper IPA concentration. |
| Models are sticky after curing. | Insufficient curing time; models not dry before curing; UV lights are dirty. | Increase curing time; ensure models are completely dry; clean UV lights. |
8. Спецификации
| Карактеристика | Детал |
|---|---|
| Модел | Миење и стврднување 3 |
| Димензии на производот | 8.86 x 8.66 x 14.88 инчи |
| Тежина на ставката | 0.01 унци |
| Бренд | АНИКУБИЧНО |
| Материјал | PC+metal |
| Боја | Мулти-боја |
| Maximum Cleaning Volume | 165 x 100 x 180 mm (4L bucket) |
| УВ светлина | 10pcs 405nm + Gooseneck Light |
| Максимална големина на стврднување | Φ160 x 180 mm |
| Тајмер | 1-30 минути прилагодливо |
Слика 8.1: Detailed comparison of Wash and Cure 3 and Wash and Cure 3 Plus specifications.
9. Гаранција и поддршка
For warranty information, technical support, or service inquiries, please refer to the official ANYCUBIC webстраницата или директно контактирајте ја нивната служба за корисници. Чувајте ја сметката за купување како доказ за купување за гаранциски побарувања.
Можете да ја посетите ANYCUBIC Official Store за повеќе производи и ресурси за поддршка.
