Упатство за користење на аналоген бас синтетизатор Behringer TD-3

1. Вовед

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Behringer TD-3 Analog Bass Line Synthesizer. Please read this manual thoroughly to ensure proper use and to maximize the performance of your instrument.

The Behringer TD-3 is an analog bass line synthesizer designed to produce classic electronic music sounds. It features an all-analog signal path, a 16-step sequencer, and a resonant low-pass filter.

2. Поставување

2.1 Отпакување

Carefully remove the TD-3 from its packaging. Retain the packaging materials for future transport or storage.

2.2 Поврзување за напојување

Connect the included DC power adapter to the 'DC IN' port on the rear panel of the TD-3. Plug the adapter into a suitable power outlet. Ensure the power switch is in the 'OFF' position before connecting power.

2.3 Аудио врски

• Главен излез: Connect the 'OUTPUT' jack (1/4" TS) on the rear panel to your mixer, audio interface, or ampживописен.
• Слушалки: Connect headphones to the 'PHONES' jack (1/4" TRS) on the front panel for private monitoring. Adjust the 'VOLUME' knob to a comfortable listening level.

2.4 MIDI/USB Connections

• MIDI Влез/Излез: Use standard 5-pin DIN MIDI cables to connect the 'MIDI IN' and 'MIDI OUT' ports to other MIDI devices for synchronization or control.
• USB: Connect the USB port to a computer for MIDI control and firmware updates.

2.5 CV/Gate Connections

The TD-3 features 'CV OUT' and 'GATE OUT' jacks (3.5mm TS) for integration with modular synthesizers and other analog control voltage equipment. These outputs transmit pitch and gate information from the sequencer.

Слика 1: Front panel and rear connections of the Behringer TD-3. This image displays the various knobs, buttons, and input/output jacks, including the power input, audio output, headphone jack, MIDI ports, USB port, and CV/Gate connections, all essential for setting up the device.

3. Operating the TD-3

3.1 Вклучување

After all connections are made, switch the 'POWER' button on the rear panel to the 'ON' position. The unit will power up.

3.2 Контроли надview

The TD-3's front panel is divided into several sections:

• VCO (томtage Controlled Oscillator): Controls the basic sound waveform and pitch.
• VCF (томtage Контролиран филтер): Shapes the timbre of the sound.
• Плик: Controls the decay of the filter.
• Секвенсер: Programs and plays musical patterns.
• Искривување: Adds overdrive to the sound.
• Волумен: Го прилагодува вкупното ниво на излез.

3.3 VCO Section

• ПРЕСУДА: Го прилагодува вкупниот тон на осцилаторот.
• БРАНОВ ФОРМА: Selects between Sawtooth (bright, rich harmonics) and Square (hollow, reedy) waveforms.

3.4 VCF Section

• ОТСЕЧЕН: Sets the frequency at which the filter begins to attenuate higher frequencies.
• РЕЗОНАНЦА: Emphasizes frequencies around the cutoff point, creating a 'wah' effect at higher settings.
• плик: Controls the amount of filter envelope modulation applied to the cutoff frequency.
• ДЕКАЈ: Determines the length of the filter envelope's decay phase.
• АКЦЕНТ: Controls the intensity of the accent effect on notes.

3.5 Sequencer Operation

The TD-3 features a powerful 16-step sequencer for creating bass lines.

• Прекинувач MODE: Selects between 'WRITE' (for programming patterns) and 'PLAY' (for playing patterns or tracks).
• TRACK/PATTERN Selector: In 'PLAY' mode, choose between playing a single 'PATTERN' or a 'TRACK' (a chain of patterns). In 'WRITE' mode, select 'TRACK' to edit a track or 'PATTERN' to edit a pattern.
• PATTERN GROUP: Selects one of four groups (I, II, III, IV), each containing 8 patterns (1-8).
• ТЕМПО: Ја прилагодува брзината на репродукција на секвенцерот.
• СТАРТ / СТОП: Ја започнува или ја запира репродукцијата на секвенцерот.
• ПИШУВАЈ/СЛЕДНО: Used to confirm steps during pattern writing or to advance to the next step.
• PITCH MODE: Selects the input source for pitch information (INT for internal keyboard, MIDI, USB, TRIG for external trigger).
• РЕEИМ НА ВРЕМЕ: Sets the clock resolution for external synchronization (1PPS, 2PPQ, 24PPQ, 48PPQ).
• ФУНКЦИЈА копчиња: These buttons (DEL, INS, CH, COPY, PASTE, TRANSPOSE, ACCENT, SLIDE) perform various editing functions within the sequencer.
• STEP Buttons (1-8, 9, 0, 100, 200): Used for entering notes, selecting steps, and other functions depending on the mode.

3.6 Distortion Section

• ВКЛУЧЕН/ИСКЛУЧЕН прекинувач: Engages or bypasses the built-in distortion effect.
• ДИСТОРЗИЈА: Ја прилагодува количината на пребрзување.
• ТОН: Shapes the frequency content of the distorted sound.
• НИВО: Го контролира излезното ниво на ефектот на дисторзија.

3.7 Контрола на јачината на звукот

The 'VOLUME' knob adjusts the overall output level of the TD-3. Use this to balance the TD-3's output with other instruments in your setup.

4. Одржување

4.1 Чистење

Clean the TD-3 with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the finish and internal components.

4.2 Складирање

When not in use, store the TD-3 in a cool, dry place away from direct sunlight and extreme temperatures. If transporting, use the original packaging or a suitable protective case.

4.3 Ажурирања на фирмверот

Периодично проверувајте го Behringer-от website for available firmware updates. Updates can provide new features, improvements, and bug fixes. Follow the instructions provided with the firmware update carefully.

5 Смена на проблеми

5.1 Нема излез на звук

• Проверете дали адаптерот за напојување е правилно поврзан и дали уредот е вклучен.
• Проверете ги сите аудио кабли за правилно поврзување и интегритет.
• Verify the 'VOLUME' knob is turned up.
• If using headphones, ensure they are fully plugged in and the volume is adjusted.
• Confirm that a pattern is playing and the 'MODE' switch is set to 'PLAY'.

5.2 Sequencer Not Playing

• Press the 'START/STOP' button to initiate playback.
• Ensure the 'MODE' switch is set to 'PLAY'.
• Check the 'TEMPO' knob setting; it might be set to a very slow speed.
• If synchronized externally, verify the external clock source is active and the 'TIME MODE' is correctly set.

5.3 MIDI Control Issues

• Ensure MIDI cables are connected correctly (MIDI OUT of controller to MIDI IN of TD-3).
• Verify that the TD-3 and your MIDI controller are on the same MIDI channel.
• Check the 'PITCH MODE' setting on the TD-3 to ensure it is set to 'MIDI' or 'USB' as appropriate.

6. Спецификации

7. Гаранција и поддршка

Behringer products are designed and manufactured to high standards. For detailed warranty information and technical support, please refer to the official Behringer webлокација или контактирајте го вашиот локален дистрибутер. Чувајте ја сметката за купување како доказ за купување за гаранциски побарувања.

За понатамошна помош, посетете ја Продавница „Берингер“ на Амазон or the official Behringer support page.