Упатство за користење на преносен 3-во-1 осцилоскоп, мултиметар и генератор на бранови форми HANMATEK HO51

1. Вовед

The HANMATEK HO51 is a versatile, portable 3-in-1 device that integrates the functions of a digital oscilloscope, a multimeter, and a waveform generator. Designed for electronic troubleshooting, testing, and educational purposes, it offers a compact solution for various measurement needs. Its user-friendly interface and robust design make it suitable for both beginners and experienced professionals.

Клучни карактеристики:

• Функционалност 3-во-1: Combines an oscilloscope, multimeter, and waveform generator in a single compact unit.
• осцилоскоп: 50 MHz bandwidth and 250 MS/s real-time sampling rate for precise waveform analysis.
• Мултиметар: Accurate measurements of voltage, current, resistance, capacitance, continuity, and diode tests.
• Генератор на бранови форми: Generates sine, square, triangle, and custom waveforms up to 1 MHz.
• Преносен дизајн: Lightweight and compact (198mm x 100mm x 39mm, 0.5 kg) for easy transport and field use.
• Прикажи: 3.5-inch color screen with an intuitive interface.
• Компатибилност со софтвер за компјутер: USB connectivity for data transfer and advanced control.
• Моќност: Operates on battery or via USB power.

Image 1.1: The HANMATEK HO51's integrated Oscilloscope, Multimeter, and Waveform Generator functions.

2. Информации за безбедност

Please read all safety instructions carefully before operating the device. Failure to follow these instructions may result in electric shock, fire, or damage to the device.

• Не го користете уредот ако изгледа оштетен или не работи правилно.
• Ensure proper probe connections and settings before taking measurements.
• Не ги надминувајте максималните влезни оценки за јачина на звукtage и струја.
• Use only the accessories provided or approved by HANMATEK.
• Избегнувајте ракување со уредот во влажни или суви услови.amp услови.
• Disconnect power from the circuit under test before connecting or disconnecting probes.
• Секогаш почитувајте ги локалните и националните безбедносни кодови.

3. Содржина на пакетот

Проверете дали сите артикли наведени подолу се вклучени во вашиот пакет. Доколку некои артикли недостасуваат или се оштетени, ве молиме контактирајте го вашиот продавач.

• HANMATEK HO51 Device
• USB-кабел (тип-C)
• Пасивна осцилоскопска сонда
• Мултиметарски тест кабли
• Водич за брз почеток
• Probe Calibration Tool
• Адаптер за напојување
• Мека торбичка за носење

Image 3.1: HANMATEK HO51 device and included accessories.

4. Производот завршиview

The HANMATEK HO51 features a clear layout for easy operation. Familiarize yourself with the buttons, connectors, and display area.

4.1 Контроли и дисплеј на предниот панел

Image 4.1: Front panel layout and controls of the HANMATEK HO51.

• Област на прикажување: 3.5-inch color screen for waveform, measurement data, and menu display.
• F1-F4 Keys: Multi-function keys, their purpose changes based on the current menu.
• Копче за режим: Префрлува помеѓу режимите на осцилоскоп, мултиметар и генератор на бранови форми.
• CH Key: Channel selection (if applicable) or related settings.
• HOR Key: Horizontal scale adjustment for oscilloscope.
• Системски клуч: Accesses system settings, including language selection.
• Зачувај клуч: Saves current waveform data or measurement results.
• Trig/Δ Key: Trigger menu for oscilloscope or relative value key for multimeter.
• Автоматски клуч: Automatic setting for oscilloscope or automatic range key for multimeter.
• Measure Range Key: Measurement menu for oscilloscope or range key for multimeter.
• Копче за прекинувач за напојување: Го вклучува/исклучува уредот.
• Клуч за репродукција/пауза: Stops/runs oscilloscope acquisition or holds value for multimeter.
• Копчиња за навигација: Up, Down, Left, Right for menu navigation and parameter adjustment.
• Влезни порти за мултиметар: A, mA, COM, QVC for connecting multimeter test leads.

4.2 Side and Bottom Connectors

Слика 4.2: Страна view showing Type-C charging port and rear stand.

• Пристаниште за полнење од тип C: Located on the side for charging the internal battery and USB communication with a PC.
• Probe Compensation / Signal Generator Output Connector: Located on the top side, provides a 2.5V/1KHz square wave signal for probe calibration and serves as the waveform generator output.
• Measured Signal Input Connector (BNC): Located on the bottom for connecting the oscilloscope probe.
• Заграда: An expandable stand on the back allows for convenient viewинг агли.

5. Поставување

5.1 Почетно полнење

Before first use, fully charge the device using the provided USB Type-C cable and power adapter. The charging indicator will show the charging status.

5.2 Вклучување/исклучување

Притиснете и задржете го Копче за прекинувач за напојување (обично означено со симбол за напојување) за да го вклучите или исклучите уредот.

5.3 Избор на јазик

Upon first startup, the device may be in a default language. To change the language:

1. Притиснете го Систем клуч.
2. Navigate to the language settings (often labeled F2 or similar).
3. Select your desired language (e.g., English) using the navigation keys and confirm.

5.4 Oscilloscope Probe Calibration

For accurate oscilloscope measurements, calibrate the passive probe before use:

1. Connect the oscilloscope probe to the BNC input connector on the bottom of the device.
2. Connect the probe tip to the probe compensation/signal generator output connector (1KHz square wave) on the top side of the device.
3. Enter Oscilloscope mode (if not already there) and adjust the vertical and horizontal scales to view the square wave.
4. Using the small calibration tool, adjust the screw on the probe connector until the square wave displayed on the screen has flat tops and bottoms with sharp corners, indicating proper compensation.

6. Упатства за работа

6.1 Префрлување режими

Притиснете го Режим key to cycle between Oscilloscope, Multimeter, and Waveform Generator functions.

6.2 Работа на осцилоскоп

In Oscilloscope mode, the device displays waveforms over time. Use the following controls:

• Вертикална скала (волти/дивидуал): Adjust using the navigation keys (Up/Down) when the vertical scale is highlighted.
• Хоризонтална скала (Време/Дел): Притиснете ХОР and then use navigation keys (Left/Right) to adjust.
• Поставки за активирање: Притиснете Триг/Δ to access trigger menu. Adjust trigger level, mode (Auto, Normal, Single), and type (rising/falling edge).
• Автоматско поставување: Притиснете Автоматски for automatic waveform scaling and positioning.
• Стартувај/Стоп: Притиснете го Пушти/Пауза key to start or stop waveform acquisition.

6.3 Работа со мултиметар

In Multimeter mode, the device performs various electrical measurements. Connect the multimeter test leads to the appropriate input ports (A, mA, COM, QVC).

• Избор на функција: Use the F1-F4 keys or navigation keys to select measurement functions (Voltage, Current, Resistance, Capacitance, Continuity, Diode).
• Избор на опсег: Притиснете Опсег на мерење to manually select the measurement range, or use Автоматски for automatic ranging.
• Тест за континуитет: Connect leads across a circuit. An audible tone indicates continuity. Note that some users have reported a slight delay in response for continuity tests.
• Тест за диоди: Connect leads across a diode to measure its forward voltagд капка.

6.4 Работа на генераторот на бранови форми

In Waveform Generator mode, the device outputs various signals from the probe compensation/signal generator output connector.

• Тип на брановидни форми: Use the F1-F4 keys or navigation keys to select the desired waveform (Sine, Square, Triangle, Pulse).
• Прилагодување на фреквенција: Adjust the output frequency using the navigation keys.
• AmpПрилагодување на осветленоста: Прилагодете го излезот amplitude (1Vpp or 2.5Vpp) using the navigation keys.

6.5 PC Software Connectivity

Connect the HO51 to a computer via the USB Type-C port. Compatible PC software allows for data transfer, waveform analysis, and remote control of the device. Refer to the software's documentation for detailed instructions.

Image 6.1: HANMATEK HO51 connected to a PC for data export and analysis.

7. Одржување

Proper maintenance ensures the longevity and accuracy of your HANMATEK HO51.

• Чистење: Користете мека, гamp cloth to clean the device. Do not use abrasive cleaners or solvents. Ensure the device is powered off and disconnected from any power source before cleaning.
• Складирање: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. Use the provided carrying case for protection.
• Нега на батеријата: For optimal battery life, avoid fully discharging the battery frequently. If storing for extended periods, charge the battery to approximately 50% every few months.
• Ажурирања на фирмверот: Periodically check the HANMATEK official webстраница за достапни ажурирања на фирмверот за да се обезбедат оптимални перформанси и пристап до нови функции.

8 Смена на проблеми

If you encounter issues with your HANMATEK HO51, refer to the following common problems and solutions.

• Уредот не се вклучува:
  • Ensure the battery is charged. Connect the device to a power source using the USB-C cable and adapter.
  • Притиснете и задржете го копчето за вклучување неколку секунди.
• Не се прикажува бранова форма во режим на осцилоскоп:
  • Check if the probe is correctly connected to the BNC input.
  • Verify the probe is properly calibrated.
  • Прилагодете ги вертикалните (волти/девизен) и хоризонталните (време/девизен) скали.
  • Check trigger settings; try setting the trigger mode to 'Auto' or adjusting the trigger level.
  • Ensure the 'Run' state is active (not paused).
• Multimeter readings are inaccurate or slow:
  • Ensure test leads are securely connected to the correct input ports.
  • Проверете дали се избрани точната функција за мерење и опсег.
  • For continuity tests, allow a moment for the device to register the connection, as some users have noted a slight delay.
  • Consider performing a factory reset via the System menu if persistent issues occur.
• Waveform generator output is incorrect:
  • Ensure the output is connected to the correct port.
  • Verify the selected waveform type, frequency, and ampпоставки за литуда.

9. Спецификации

Detailed technical specifications for the HANMATEK HO51 device.

9.1 Спецификации на осцилоскоп

9.2 Спецификации на мултиметар

9.3 Waveform Generator Specifications

9.4 Општи спецификации

10. Гаранција и поддршка

For warranty information, technical support, or service inquiries, please refer to the documentation included with your product or contact HANMATEK customer service directly. You may also visit the product page on Amazon for additional support resources or to contact the seller.

Страница на производот на Амазон: HANMATEK HO51 on Amazon.com.be