GODOX XT-16 Flash Trigger Transmitter User Manual

1. Вовед

The GODOX XT-16 Flash Trigger Transmitter is a wireless control device designed for Godox 2.4G X System photography monolights and studio strobe lights. It operates on a 2.4GHz frequency, offering 16 channels and 16 groups for flexible control. This transmitter enables remote adjustment of flash power, modeling lamp, buzzer, AF-assist beam, and flash triggering, providing enhanced convenience and precision in studio and on-location photography setups.

2. Поставување и инсталација

2.1 Вклучување

Ensure the XT-16 transmitter has fresh batteries installed. Turn on the power switch located on the side of the unit.

2.2 Pairing with Godox 2.4G X System Monolights

The XT-16 transmitter works directly with Godox 2.4G X system monolights such as MS300, MS300V, SK300II, SK400II, SK400IIV, DP400II, DP400III, DP600II, and DP600III. No additional receiver is required for these units.

Figure 1: Godox XT-16 trigger compatibility with various Godox 2.4G X System monolights. The image shows the XT-16 in the center, surrounded by compatible flashes like DP II, Quick II, Quicker DII, MS300, MS300-V, SK300II, SK400II, and SK400II-V, indicating direct wireless control.

2.3 Pairing with Non-2.4G X System Studio Strobes

For non-2.4G X system studio strobe lights, the Godox XTR-16 receiver is required to receive commands from the XT-16 transmitter and enable synchronization. Ensure the XTR-16 receiver is properly connected to the strobe's USB 'SYN' port.

2.4 Pairing with V850/V860 Series Flashes

When using the XT-16 with Godox V850 or V860 series flashes, the Godox XTR-16S receiver is necessary for synchronization.

2.5 Basic Setup Steps with 2.4G Strobe

1. Ensure all devices (transmitter and strobe) are powered ON.
2. Turn ON the 2.4G signal on the strobe.
3. Set the same channel on both the XT-16 transmitter and the strobe.
4. Set the POWER dial to the desired GROUP number/letter selected on the Godox 2.4G X system strobe.

Figure 2: XT-16 display and setup instructions. The image highlights the 2.4G signal indicator, channel, group, and output ratio on the XT-16's screen, alongside a step-by-step guide for connecting to a 2.4G strobe.

3. Упатства за работа

3.1 Монтирање на предавателот

Mount the XT-16 transmitter onto your camera's hot shoe. Ensure it is securely fastened.

Figure 3: XT-16 mounted on a camera. This image illustrates the XT-16 trigger attached to a camera's hot shoe, demonstrating its use in wirelessly triggering a studio strobe.

3.2 Контроли и функции

• ВКЛУЧУВАЊЕ/ИСКЛУЧУВАЊЕ: Use the dedicated switch to turn the unit on or off.
• Избор на канал: The XT-16 offers 16 channels. Use the channel selector to match the channel with your strobe.
• Избор на група: Control up to 16 groups (0-9, A-F). Select the desired group for individual or multiple strobe control.
• Прилагодување на нивото на моќност: Use the power dial to adjust the flash output level of the connected strobes.
• Моделирање Лamp ВКЛУЧЕНО/ИСКЛУЧЕНО: Toggle the modeling lamp of the strobe.
• ВКЛУЧЕНО/ИСКЛУЧЕНО Ѕвонче: Activate or deactivate the strobe's buzzer sound.
• AF-Assist Beam ON/OFF: Control the autofocus assist beam function.
• Копче за тестирање: Press to fire a test flash and verify connection.

3.3 Безжични перформанси

The XT-16 operates on a 2.4GHz frequency, providing a wireless control working distance of up to 100 meters. The fastest synchronization speed achievable is 1/250s.

4. Компатибилност

The GODOX XT-16 Flash Trigger Transmitter is widely compatible with various camera brands, including Canon, Nikon, Sony, Fujifilm, Olympus, and Pentax. It synchronizes the camera shutter with Godox X system monolights.

4.1 Camera Compatibility List

Refer to the detailed compatibility list below for specific camera models and their flash sync capabilities with the XT-16. This table indicates models that support legacy hot shoe control.

Figure 4: Camera compatibility list. This image displays a comprehensive table detailing the compatibility of various camera models from brands like Canon, Nikon, Sony, Fujifilm, Olympus, Pentax, Leica, and Panasonic with the XT-16 trigger, indicating their flash synchronization status.

Забелешка: This table only lists tested camera models. For other camera models, a self-test is recommended. Some models may require an adapter or have specific limitations (e.g., sync speed). Always refer to your camera's manual for hot shoe compatibility.

5. Одржување

• Чувајте го уредот сув. Не ракувајте со влажни раце и не го потопувајте во вода.
• Avoid sudden impacts. The device may malfunction if subjected to strong shocks, drops, or vibrations.
• Да се ​​чува подалеку од дофат на деца.
• Do not disassemble the device. Repairs should only be performed by authorized service personnel.
• Чистете го уредот со мека, сува крпа. Не користете растворувачи или груби хемикалии.
• Отстранете ги батериите ако уредот нема да се користи подолг период за да спречите протекување.

6 Смена на проблеми

6.1 Блицот не свети

• Проверете ја моќноста: Ensure both the XT-16 transmitter and the strobe/flash unit are powered on and have sufficient battery life.
• Verify Channel/Group: Confirm that the channel and group settings on the XT-16 match those on the receiving strobe/flash unit.
• Безбедна врска: Ensure the XT-16 is properly seated in the camera's hot shoe. For external receivers (XTR-16/XTR-16S), ensure they are securely connected to the flash unit.
• Опсег: Check if the transmitter and receiver are within the effective operating range (up to 100 meters). Obstacles can reduce this range.
• Поставки на камерата: Ensure your camera's flash settings are correctly configured and not set to a mode that disables external flash.

6.2 Inconsistent Firing or Missed Flashes

• Пречки: 2.4GHz signals can be affected by other wireless devices. Try changing the channel on your XT-16 and strobe.
• Ниво на батерија: Low batteries in either the transmitter or the flash unit can lead to inconsistent performance. Replace or recharge batteries.
• Растојание/Пречки: Reduce the distance between the transmitter and receiver, or remove any large metallic objects that might be blocking the signal.

6.3 Incorrect Flash Output

• Поставки за напојување: Double-check the power level set on the XT-16 transmitter.
• Режим на строб: Ensure the strobe is in the correct mode (e.g., Manual) if you are controlling power manually from the XT-16.

7. Спецификации

8. Гаранција и поддршка

For warranty information and technical support, please refer to the documentation included with your purchase or visit the official GODOX webстраница. Зачувајте го доказот за купување за какви било гаранциски побарувања.