Производот завршиview
The SUNLU S1 Plus Filament Dryer Box is designed to maintain optimal filament conditions for 3D printing. It helps prevent common printing issues caused by moisture absorption in various filament types, ensuring higher print quality and reliability.
Содржина на пакетот
- SUNLU S1 Plus Filament Dryer Unit
- Адаптер за напојување
- Упатство за употреба
- Filament Guide Tubes (small white gaskets)
Инструкции за поставување
- Place the filament spool into the drying chamber. The dryer supports various spool sizes and filament diameters (1.75mm, 2.85mm, 3.00mm).
Image illustrating the compatibility of the SUNLU S1 Plus Filament Dryer with various filament spool sizes and diameters (1.75mm, 2.85mm, 3.00mm). - Select the appropriate filament outlet hole (top or front) based on your 3D printer's inlet position. Use the provided guide tubes if necessary.
- Connect the power adapter to the dryer and a power source.
Operating the Filament Dryer
The SUNLU S1 Plus features a 2-inch LCD screen and two control buttons for easy operation.
Вклучување/исклучување
- To power on, press the Left or Right button.
- To power off, press both buttons simultaneously.
Поставување на температурата
- After powering on, press the Left or Right button to set the target temperature. The adjustable temperature range is 35°C to 55°C.
- Refer to the material-specific temperature guidelines in the manual for optimal drying.
Поставување време
- Hold the Left button to enter time setting mode.
- Press Left or Right to adjust the drying duration (1-99 hours).
- Hold the Left button again to confirm and exit.
Екран за влажност
- Hold the Right button to display the current chamber humidity (%RH).
- Hold the Right button again to exit the humidity display.
Filament Compatibility and Recommended Settings
The dryer is compatible with a wide range of 3D printing filaments. Below are general recommended settings:
| Материјал | Baking Temp (°C) | Време (ч) |
|---|---|---|
| PLA | 45-50 | 3-6 |
| ДРВО | 45-50 | 3-6 |
| PVB | 45-50 | 3-6 |
| ABS | 50-55 | 3-6 |
| БОЛКИ | 50-55 | 3-6 |
| PC | 50-55 | 3-6 |
| PA | 50-55 | 3-6 |
| ASA | 50-55 | 3-6 |
| PETG | 47-51 | 3-6 |
| TPU | 47-51 | 3-6 |
Забелешка: The operating temperature range for this product is 20°C to 35°C. If the ambient temperature is below 10°C, it may fail to start normally, which is considered a normal occurrence.
Одржување
- Regularly inspect the filament path for any debris or blockages.
- Keep the dryer clean and free from dust to ensure optimal performance.
- Store the dryer in a dry environment when not in use.
Решавање на вообичаени проблеми
Poor Print Quality (Stringing, Blobs, Poor Adhesion)
- Причина: Filament has absorbed moisture.
- Решение: Increase drying time or temperature within recommended ranges. Ensure filament is thoroughly dried before and during printing.
Сушарата не се загрева
- Причина: Ambient temperature is too low (below 10°C).
- Решение: Operate the dryer in an environment within the recommended temperature range (20°C to 35°C).
Спецификации на производот
- Големина на производот: 271(L)x100(Ш)x237(В)мм
- Max Coil Size: Ø210*85(H)mm
- Нето Тежина: 980 гр
- Дијаметар на влакно: 1.75/2.85/3.0mm
- Работна влажност: 90%
- Работна температура: 35°C-55°C
- Влезна моќност: AC 100V-240V, 50/60HZ
- Излезна моќност: DC 24V ± 1.2V, 2A
- Standby Power: 0.05 W
- Max Working Electricity: 1.8A
- Максимална работна моќност: 48 W
- Големина на LCD екран: 2 инчи
Гаранција и поддршка
The product comes with a one-year warranty under normal operating conditions as described in this manual.
Гаранцијата не ги покрива штетите предизвикани од употреба на кабли за напојување со различни спецификации или неправилно работење според упатствата во упатството за време на гарантниот период.
For after-sales service and support, please visit the official SUNLU webсајт или контактирајте со нивниот тим за поддршка.
