Водич за управување со додатоци на Auri Q-Sys - Упатство за користење на софтверот за управување со додатоци
Историја на верзијата
| Auri TX2N 1.0.0.4 | август 2025 година | Првично издание |
| Auri D4/D16 1.0.0.1 | август 2025 година | Првично издание |
Компатибилност
Додатокот Auri TX2N работи со предаватели Auri TX2N и Auri TX2N-D.
The Auri Docking Station plugin works with Auri D4 and Auri D16 Docking Stations.
Devices must be on firmware version 1.5 or above to support the plugin.
For each device, the API must be enabled before attempting connection with the plugin. The API is disabled by default and must be enabled via the Settings page of each device in Auri Manager. See the system manual for more details on how to configure your device.
Конфигурација на поставки
| IP адреса | Enter the IP address of the device to connect. This can be retrieved by checking the device listing page in Auri Manager. |
| Статус | Reports plugin and driver status. |
| Device Type* | Reports the device connected, TX2N, TX2N-D, D4 or D16. |
| Device Name* | Reports the name of the device connected. |
| Serial Number* | Reports the serial number of the device connected. |
| MAC Address* | Reports the MAC address of the device connected. |
| Software Version* | Reports the firmware version of the device connected. |
| Meter Rate (TX only) | Set how often the signal meters are polled in seconds (0.5 to 120). |
| Control Rate | Set how often other controls are polled in seconds (5 to 120). Use these options to balance responsiveness of any controls shown on a UI against the level of network traffic needed. |
| Идентификувајте | Sends the identify command to flash the device LED for 30s. |
| Key Length (TX only) | Defines the length of randomized key to be generated, between 4-16 characters. Shorter keys should only be used when users will need to enter the key manually, for higher security when using RX1 receivers and QR codes the full 16 characters are recommended. |
| Key Type (TX only) | Defines the character set of randomized key to be generated, numbers, letters, alphanumeric or extended ASCII (adds a range of sup- ported special characters). The larger character set used the higher the security. As with key length this should be balanced with ease of use if manual entry is required. |
Овие полиња ќе бидат пополнети за секој Auri уред што е поврзан онлајн, без оглед на тоа дали API-то е овозможено или не.
Влезови (само TX)
| Stream 1 Input 1 Mute | Mutes the local inputs (analogue or Dante) to stream 1. |
| Stream 1 Input 2 Mute | Mutes the network audio inputs to stream 1. |
| Stream 1 Signal L/R | Reports back the signal level (post mix) for stream 1, between -96dB and 0dB. |
| Stream 2 Input 1 Mute | Mutes the local inputs (analogue or Dante) to stream 2. |
| Stream 2 Input 2 Mute | Mutes the network audio inputs to stream 2. |
| Stream 2 Signal L/R | Reports back the signal level (post mix) for stream 1, between -96dB and 0dB. |
Излез 1/2 (само TX)
| Radio Output | Toggles the radio output on or off. |
| Broadcast Name | Sets the name for that broadcast, changing this will restart the radio. |
| Program Info | Sets the descriptive contextual information about the broadcast. |
| Енкрипција | Toggles the encryption on or off for the broadcast. |
| Privacy Key | Sets the privacy key to be used if encryption is enabled. |
| Regenerate Key | Generates a new randomized privacy key based on the options set on the Config tab. |
| QR Code | Shows a QR code to allow Auracast assistants to connect devices to the broadcast. This includes the Broadcast Name, and if Encryption is enabled and a Privacy Key is set, the key will also be included. |
Библиотека 1-16 / 17-32 (само за Д)
| Broadcast Name (1-32) | Allows broadcast name to be populated for each of the 32 entries in the docking station library, to be transferred to docked RX1 receivers. |
| Privacy Key (1-32) | Allows privacy key to be populated for each of the 32 entries in thedocking station library, to be transferred to docked RX1 receivers. |
Статус излези
| Статус | Порака | Значење |
| ИСЧЕЗНАТИ | No IP | IP address field is blank. |
| ИНИЦИЈАЛИЗИРАЊЕ | Поврзување | Plugin is establishing initial connection to the device. |
| ИНИЦИЈАЛИЗИРАЊЕ | Testing API… | Successful initial connection has been made, establishing if API is enabled and responding. |
| OK | Поврзан | Device is responding to commands and reporting a valid system status. |
| ВИНА | Invalid IP | IP address is not valid. |
| ВИНА | Unsupported device type: | Device has responded but is not supported by the plugin, ensure you are using the correct plugin for TX2N or D4/ D16. |
| ВИНА | Device Error Code: X | Device is in an error state, consult the user manual and Auri Manager to resolve. |
| ВИНА | Device Offline / NoResponse | No response from the provided IP address. Check IP address and ensure device has power and network connectivity. |
| ВИНА | API Not Enabled | Device initial response received but no response from API.Check firmware version and API setting in Auri Manager. |
| ВИНА | Cannot create JSON UDP socket – try different IP or restart | Plugin is unable to open a UDP socket to the device on port55666. Check network configuration. |
| ВИНА | JSON service error – change IP to reconnect | Invalid response from the device’s info service, check AuriManager to confirm device is responding as expected. |
| ВИНА | Invalid JSON response | Invalid response from the device’s info service, check AuriManager to confirm device is responding as expected. |
| ВИНА | Cannot create UDP socket – try different IP or restart | Plugin is unable to open a UDP socket to the device for API on port 54666, confirm device firmware is up to date and API enabled, check network configuration. |
| ВИНА | UDP socket lost – change IP to reconnect | Connection has been interrupted, change the IP address orrestart the plugin to reinitialize the connection. |
| ВИНА | Network error – change IP to reconnect | Connection has been failed, change the IP address orrestart the plugin to reinitialize the connection. |
Својства
| Show Debug | Enables debug window. Dev only. |
| Debug Print | Selects which plugin actions should print to debug window. Dev only. |
User Interface – TX2N
User Interface – D4 / D16
Меѓусебно поврзување Plugins
На plugins изложете ги сите клучни елементи како контролни пинови, овозможувајќи ви да ги поврзете со други делови од дизајнот на вашиот Q-Sys. Еден клучен случај на употреба е да се осигурате дека промените во емитувањата на TX2N се синхронизирани со докинг станиците, така што сите докинг приемници ќе можат да се поврзат.
AMPЕТРОНИЧКА Unit 2, Trentside Business Village, Farndon Road, Newark NG24 4XB, United Kingdom
Телефон: +44.1636.610062 www.ampetronic.com
СЛУШАЈТЕ ТЕХНОЛОГИИ 14912 Хериtage Crest Way, Bluffdale, Јута 84065-4818 САД
Телефон: + 1.801.233.8992
Бесплатен: 1.800.330.0891
www.listentech.com
Документи / ресурси
 | Софтвер за управување со водичи за додатоци на Q-Sys |
Референци
- AmpЕтронски двигатели на системот за јамка за слух и дизајн на јамка - 60118-4www.ampetronic.com
- Дома - Слушајте технологииwww.listentech.com
- Упатство за употребаmanual.tools