Shenzhen GUSGU Intelligent Interactive Screen Game Controller

Спецификации

• Име на производ: Intelligent interactive screen game controller
• Големина на производот L160 * W106 * H65 mm
• Оценет влез 5V == 500mA
• Номинален капацитет 1000 mAh
• Тежина на производот 282g($50g)
• Стандарди за извршување МК 4943.1-2022
• Десното рамо key/RB
• Десен активирач/RT
• Левото рамо button/LB
• Лево активирање/LT

Содржина на пакувањето

Вовед во производот

Безбедносни информации
Before using this product, please read the following safety instructions anc ollow all regular satety precautions. Any operation that does not comply with this manual may result in damage to this product.

ПРЕДУПРЕДУВАЊЕ

1. Do not place the device near heat sources or exposed fire sources, or other places that may generate high temperatures.
2. Ако батеријата не се замени правилно, постои ризик од експлозија.
3. Не обидувајте се да ја замените внатрешната литиум-јонска батерија што се полни.
4. If the product experiences severe swelling, do not continue to use it.
5. Do not squeeze or place the product in a place where it is easy to fall off.
6. Do not attempt to disassemble the battery. Otherwise, it may cause anattery explosion or liquid leakage inside the battery. Batteries not specified by the manufacturer or batteries that have been disassembled and modified are not covered by the warranty.

Обрнете внимание на

1. Electromagnetic waves of specific frequencies may affect the normal use of products.
2. Before you start working with the product, please read the instruction manual and operate it once to master its use proficiently.
3. Кога машината ќе се расипе, не ја расклопувајте или поправајте произволно. Само овластен персонал за одржување може да врши поправки на машината.
4. If not used for a long time, please charge the device to about 50% every three months before storing it to effectively extend the battery life. Please fully charge it before use.

Вовед во функција

1. The controller supports wired connection mode, Bluetooth connection mode, and 2.4G connection mode according to different platforms.
2. The Bluetooth/2.4G modes support Android 9 and above, Windows 10 and above, iOS 14 and above, and Nintendo Switch consoles.
3. The wired mode supports Nintendo Switch, Android 9, Windows 10, X-input (PC360),
4. Smart Screen Operation Guide
   When the controller is in standby mode, long-press the HOME key to enter the smart screen operation menu. At this time, the controller can set the smart screen

Работа за вклучување/исклучување

Вклучете го: Short-press the “H” key to turn on the device. Shutdown: Press and hold the “H” key for 5 seconds to shut down, or press and hold the “H” key for 3 seconds to enter the menu interface. Select “Shutdown” from the menu to perform the shutdown operation.n

Автоматско исклучување: When connected, it will automatically shut down after 5 minutes without any operation, and when disconnected, it will automatically shut down after 3 minutes without any operation

Handle the connection operation

Жичен
Connect the controller to the USB interface of the device using a USB cable, and the controller will display the connection status of the corresponding device, as shown in the following figure. “X” represents XInput mode, and “D” represents DirectInput mode. P, Android wired connection defaults to Xinput mode, Switch wired connection defaults to Switch mode. Wired connection protocol does not support iOS devices

PC wired connection mode switching(Same operation in 2.4G mode)
Simultaneously press the window key and menu key for 2 seconds, and there will be a vibration prompt when switching successfully. The corresponding abbreviated letters for the mode will also switch

Безжична врска

PC Bluetooth connection

1. Controller selection mode: Press and hold the “H” key on the controller for about 3 seconds to enter the menu, select “Mode” in the menu, and then select “PC” to complete the mode switching
2. Entering pairing: After switching modes, enter pairing mode and find the Bluetooth pairing name “Xbox Wireless Controller” in the device’s Bluetooth list. Select “Pairing” from the menu to pair and connect. After a successful connection, the controller will vibrate and prompt
3. If the startup display shows the computer symbol and “Reconnecting”, the controller will automatically reconnect to the paired computer

Switch Bluetooth connection

1. Controller selection mode: Press and hold the “H” key on the controller for about 3 seconds to enter the menu, select “Mode” in the menu, and then select “Switch” to complete the mode switching
2. Внесете спарување: Press the “H” key for about 3 seconds to enter the menu, select “Pairing”, and the homepage will display “Pairing in Progress”
3. Open “Change Grip/Order” on the Switch console to pair and connect
4. If the startup display shows the Switch symbol and “Reconnecting”, the controller will automatically reconnect to the paired host

Приклучок за приемник

1. Controller selection mode: Press and hold the “H” key on the controller for about 3 seconds to enter the menu, select “Mode” in the menu, and then select “Dongle” to complete the mode switching
2. Press the “H” key for about 3 seconds to enter the menu settings. Select ” Pairing” and press the “A” key. The homepage will display “Pairing in Progress”
3. Insert the receiver into the computer, press the receiver button until the indicator light flashes to pair and connect. After a successful connection, the controller will vibrate and prompt
4. If the startup display shows the receiver symbol and “Reconnecting”, the controller will reconnect to the paired receiver.

Android Bluetooth Dinput Connection

1. Controller Selection Mode: Press and hold the “H” key on the controller for about 3 seconds to enter the menu, select “Mode” in the menu, and then select “Android” to complete the mode switching
2. Entering pairing: After switching modes, enter pairing mode and find the Bluetooth pairing name “Gamepad” in the device’s Bluetooth list. Select “Pairing” from the menu to pair and connect. After a successful connection, the controller will vibrate and prompt
3. If the startup display shows the Android symbol and “Reconnecting”, the controller will automatically reconnect to the paired Android device

PS4 врска
First, connect the PS4 host with a data cable. After a successful connection, there will be a vibration prompt, and the P4 interface will be displayed. At this point, unplug the data cable to wirelessly connect to the PS4 host. When the PS4 host is turned off, it needs to be reconnected to the PS4 host with a data cable.e

Bluetooth connection for mobile phone/tablet

1. Controller selection mode: Press and hold the “H” key on the controller for about 3 seconds to enter the menu, select “Mode” in the menu, and then select “Phone” to complete the mode switching
2. Entering pairing: After switching modes, enter pairing mode. Find the Bluetooth pairing name “Xbox Wireless Controller” in the device’s Bluetooth list, select “Pairing” in the menu to pair and connect. After a successful connection, the controller will vibrate and prompt
3. If the startup display shows the phone/tablet symbol and “Reconnecting”, the controller will automatically reconnect to the paired phone/tablet device

Macro programming function
Press and hold the “H” key on the controller for about 3 seconds to enter the menu. Select “Set” from the menu, and then select “Progran” to complete the action keys that need to be programmed (such as left joystick(up, down, left, right), (up, down, left, right), ABXY, LB\ RB\ LT\RT \ R3 \ L3). Set the back key programming according to the game scene. After setting, there will be a vibration prompt, which will take effect after returning to the homepage. The programming keys can enter blank values. To clear the value of a single programming key, you can click “Confirm” without entering the key, or select “Clear Program” to clear all macro programs. ing

Мртва лента
Press and hold the “H” key on the joystick for about 3 seconds to enter the menu. Select “Settings” from the menu, then choose “Joystick Dead Zone” to adjust as needed. After setting, there will be a vibration prompt, which will take effect after returning to the homepage.

Осветленост на екранот
Press and hold the “H” key on the controller for about 3 seconds to enter the menu. Select “Settings” from the menu, and then choose “Screen Brightness” to complete the selection as needed. After setting, there will be a vibration prompt, which will take effect after returning to the homepage.

Vibration regulation

Смени јазик
Press and hold the “H” key on the controller for about 3 seconds to enter the menu. Select “Set” from the menu, and then choose “Language” to switch between Chinese and English. The settings will take effect immediately after completion.

Распоред
Press and hold the “H” key on the controller for about 3 seconds to enter the menu. Select “Settings” from the menu, then choose “Layout Switch” “, and choose to switch between Xbox or Switch layouts as needed. After setting, there will be a vibration prompt, which will take effect after returning to the homepage.

Handle calibration

1. Calibration of the joystick
   Press and hold the “H” key on the joystick for about 3 seconds to enter the menu. In the menu, enter the “calibration” interface, select “joystick” in “joystick calibration”, ‘, and follow the pop-up prompt “please rotate the left and right joysticks at the same time” to complete the calibration There will be a prompt when the calibration is completed and it will automatically pop back to the ” calibration” interface. If the calibration fails, there will be a prompt. Restart the calibration
2. Calibration of Gyro
   Select “Calibration” on the “Gyro” interface, and follow the pop-up prompt” Please place the handle on a horizontal plane and do not move the handle during the calibration process” to complete the calibration There will be a prompt when the calibration is completed, and it will automatically return to the “Calibration” interface. There will also be a prompt when the calibration fails
3. Calibration Triggerer
   Select “Calibration” on the “Trigger” interface, follow the prompt to “press the trigger” to complete the calibration, and automatically return to the “Calibration” interface. There will also be a prompt for calibration failure.e

Key tesДолго притиснетеss the “H” key on the controller for about 3 seconds to enter the menu. In the menu, enter the “Testing” interface, where you can test all keys except for the window key (A, B, X, Y, LB, LT, RB, RT, L, R, Start (menu key), Cap (screenshot key), H. M1. M2. N1. N2. Test using thecross-directionall key, left joystick, and right joystick. Once the test is complete, press the Windows key to return.n

Соматосензорно мапирање
Press and hold the “H” key for about 3 seconds to enter the menu. Select” Mapping” in the menu, and after setting it up, there will be a vibration prompt. It will take effect after returning to the homepage.

Continuous sending function

1. Turbo settings
   Press and hold the “H” key on the joystick for about 3 seconds to enter the menu. Select “Turbo” from the menu. After entering the “Turbo” menu, you can use the left joystick to move the options and press the menu key to confirm the settings for the continuous firing mode,speedd, and Turbo clearing.
2. Artificial and Auto Turbo settings
   In the “Turbo Settings” menu, move the options to “Turbo Key Settings” and select the semi-automatic or fully automatic Turbo key as needed (Turbo supported keys: A. B. X. Y. LT. LB. RT. R , For example, if you press “A” and then press ” confirm” to return, the controller will activate the “A” key for continuous firing. After setting, there will be a vibration prompt, which will take effect after returning to the homepage.

Light mode adjustment method
Decorative lighting settings: Press the SET key to cycle between setting the 10 colors of the joystick decorative light and turning it off

Ресетирање на функција
In the power-on state, use a sufficiently long card needle to poke the reset button in the reset hole, and the handle can be forcibly turned off and reset

Изјава на FCC
Овој уред е во согласност со дел 15 од Правилата на FCC. Работата е предмет на следниве два услови:

1. Овој уред може да не предизвикува штетни пречки и
2. Овој уред мора да ги прифати сите примени пречки, вклучително и пречки што може да предизвикаат несакано работење.

Оваа опрема е тестирана и е утврдено дека е во согласност со ограничувањата за дигитален уред од класа Б, според дел 15 од Правилата на FCC. Овие ограничувања се дизајнирани да обезбедат разумна заштита од штетни пречки во станбена инсталација. Оваа опрема генерира, користи и може да зрачи енергија на радио фреквенција и, доколку не е инсталирана и употребена според упатствата, може да предизвика штетни пречки во радио комуникациите. Сепак, не постои гаранција дека нема да има пречки во одредена инсталација. Доколку оваа опрема предизвика штетни пречки на радио или телевизиски прием, што може да се утврди со исклучување и вклучување на опремата, корисникот се охрабрува да се обиде да ги поправи пречките со една или повеќе од следниве мерки:

• Преориентирајте ја или преместете ја приемната антена.
• Зголемете го одвојувањето помеѓу опремата и приемникот.
• Поврзете ја опремата со штекер на коло различно од она на кое е поврзан ресиверот.
• Консултирајте се со продавачот или со искусен радио/телевизиски техничар за помош.

Внимание: Сите промени или модификации на овој уред кои не се експлицитно одобрени од производителот може да го поништат вашето овластување за ракување со оваа опрема.

Информации за изложеност на RF
Уредот е оценет за да ги исполни општите барања за изложеност на RF. Уредот може да се користи во пренослива состојба на изложеност без ограничување.

Најчесто поставувани прашања

Q: Can I customize the functions of the buttons and triggers?
A: Yes, you can often customize the functions of the buttons and triggers through the device’s settings or compatible software.

П: Како да го исчистам уредот?
A: Користете мека, сува крпа за нежно да ја избришете површината на уредот. Избегнувајте употреба на груби хемикалии или абразивни материјали што можат да го оштетат производот.

Документи / ресурси

Shenzhen GUSGU Intelligent Interactive Screen Game Controller [pdf] Упатство за користење 2BPUK-GUSGUG7, 2BPUKGUSGUG7, gusgug7, GUSGU Intelligent Interactive Screen Game Controller, GUSGU, Intelligent Interactive Screen Game Controller, Interactive Screen Game Controller, Screen Game Controller, Game Controller, Controller

Референци

• Упатство за употреба